Re: Communication between subnets
BranoB wrote:Upstairs ER-Xswitch0 eth1,2,3,4eth0 - connected to modem, no VID, no PVIDeth1 - connected to downstairs - VID 10,20 eth2 - connected to hdhomerun - PVID 10 Downstairs ER-Xswitch0...
View ArticleRe: Create nat rule to route traffic from eth1 to vtun0
So I removed the line and added the nat group I see in the policy link that 2 tables were created. One for each isp. Since I only have 1, do I just create 1 table?
View Articleipsec site-to-site tunnel hangs after several minutes no log entry on ERL side
# respective log entries pulled from 5506x ASA on the other end 9/12/2016 14:37 172.16.2.1 Warning %ASA-4-752012: IKEv1 was unsuccessful at setting up a tunnel. Map Tag = outside_map. Map Sequence...
View ArticleRe: ipsec site-to-site tunnel hangs after several minutes no log entry on ERL...
initial connect entires ubnt@ubnt:~$ sudo ipsec up peer-sombody.no-ip.org-tunnel-1 initiating Main Mode IKE_SA peer-sombody.no-ip.org-tunnel-1[3] to their.ip.xx generating ID_PROT request 0 [ SA V V V...
View ArticleFIOS STATIC IP ISSUES - ER 8
Had netgear running and switched to ER-8. I provisioned new ER-8 with static ip when I ran the wizard WAN2LAN. I get no connectivity light when I plug the cat from the ONT to the ER-8. I can ping the...
View ArticleManageEngine NetFlow Analyzer + ER-X sflow - doesn't see the sflow packets
Has anyone had success with the (free tier) ManageEngine NetFlow Analyzer? - With netflow enabled, I tried nprobe on the ER-X and ntopng (on a collector host). This looked nice but it only saw a...
View ArticleRe: Communication between subnets
Alright I must have something wrong here. Here's what I did. Reset downstairs ERX to default settings.Logged in on eth0, changed default IP to 192.168.10.1, reboot switched to eth1 and set my laptop IP...
View ArticleRe: How to view all connected devices (including static) and connected VPN...
Hi Jordan, Thanks very much for the reply. "show arp" is just what I need. I have gone over the L2TP over IPSec instructions again and I found I misread the "Outside Address and Next Hop" Title. So...
View ArticleClik here to view.
Edgerouter Lite & 1gig fiber - awful performance
Hi everyone, I have been having a great deal of trouble configuring the ERL for 1gig fiber with CenturyLink. I am decently familiar with networking concepts, but this is my first dive into ubiquiti...
View ArticleRe: 1.9.0 Basic Queue Application List Blank
Not using any wizards to configure QOS and I have a very basic configuration. Single LAN, a few static leases and that's it. Should I open a support ticket? Cheers,
View ArticleRe: Edgerouter Lite & 1gig fiber - awful performance
If you are getting good results anywhere outside your network then everything seems to be good. When running speed tests you are relying not only on your connection but the connection of those servers...
View Articleunable to execute "./CA.sh -newca"
hello, can someone help me on this issue? Trying to execute this command for opnevpn ./CA.sh -newca but i get an error message (See below) cdroot@ubnt-Router:~# cd...
View ArticleRe: Edgerouter Lite & 1gig fiber - awful performance
"CL's speedtest give me 900mb/s up/down" That's a VERY STRONG INDICATOR that your on-net (on CenturyLink's network, at least to their speedtest.net server) is good, but that your transit OUTSIDE of...
View ArticleRe: Need advice on POE5 Load Balance Failover Config Issues
Thanks. I did finally figure out after poking around that I could go into Config Tree and find the "modify" parameter under Interfaces > Ethernet > Firewall. I then put "balance" in the Modify...
View ArticleClik here to view.
Re: Edgerouter Lite & 1gig fiber - awful performance
I suppose you're both right . Oh well, at least we won't run out of bandwidth! Thank you two for the wisdom, I appreciate it.
View ArticleRe: VPN to LAN
After you connect on a Windows client, what does the output of "route print" run from cmd.exe show? The client config you're showing there in the last post will set the default gateway to the OpenVPN...
View ArticleRe: VPN with certificate, not pre shared key
Did you import the ca cert into the client?
View ArticleRe: 1000Base-BX-U SFP
JonnyM wrote:Are you sure it's bidirectional fibre and not GPON? What ONT is it plugged into at the moment?I'm not 100% sure, but looking at what the fiber is plugged into it should be. The fiber at...
View ArticlePerformance issues with EdgeRouter POE
Hi all, I've been trying to find the solution for this for a while now. Please note that this is my first EdgeRouter so I have probably done something wrong. However - the issue is that everything...
View Article