Re: VLAN offload
You left out the offload section. Try: configure set system offload ipv4 forwarding enable set system offload ipv4 vlan enable commit save exit
View ArticleRe: Edgerouter pro DNS forward stops on dual Wan failover
Post your config file or read the KB regarding global dns - LINK.
View ArticleClik here to view.
Re: VPN to LAN
Hello , this is the result of print route with out "redirect-gateway def1", and the status is the same, can't reach the LAN.
View ArticleEdgeOS QOS (Advanced Queue) Not Working
I have a Edgerouter X, with the following setup: eth0 as WAN, connected to my DSL modem (7.2 down 1.0 up)eth3 connected to a ethernet switch, with computers, printers, etc. connected (192.168.1.*)eth4...
View ArticleRe: SoftEther VPN for Edgerouter
Having just ordered a ER-X as a plaything, I'm building out a mipsel Debian development environment and hope to have SoftEther binaries for ER-X available in the next few days, if anyone wants to try...
View ArticleRe: EdgeRouter Pro - Is there a way to log the VPN User connection and...
jestep_97 wrote:@UBNT-stig yea, but I would think there should be some logging on the router itself, so are you saying it is impossible to do via the router?Impossible - no, but given our limited...
View ArticleRe: cannot sign a certificates
http://community.ubnt.com/t5/EdgeMAX/easy-rsa-scripts-removed-ER-X-v1-7-0rc1/m-p/1275547#M71145
View ArticleClik here to view.
Re: EdgeRouter Pro - Is there a way to log the VPN User connection and...
was afraid you were going to say something like that. Well, if someone could point me in the right direction to handle possible events I would love to figure it out. As for USG, good news. I...
View ArticleClik here to view.
Re: ERL3 to ERL3 IPsec WebGui
please see below. still no connection to and from both sites. am i missing something?
View ArticleClik here to view.
ERPoE5 PPPoE missing IP
I playing around with my ERpoe5. by configuring PPPoE using wizard, i do receive pub ip address for my pppoe. since my ISP have pppoe that require usage of vlan of 500 for TM Unifi (malaysia). so, i...
View ArticleRe: ER and haproxy
I spent a lot of time researching and configuring Pound as a reverse proxy for my needs here at home. I would be interested in having any proxy as a configurable service in the router. HAProxy was my...
View ArticleRe: VPN with certificate, not pre shared key
I'm about 50-50 on new CA installations for getting it to work right without a lot of pain. Usually I generate keys in a BSD virtual machine rather than on my mac, but it looks right. I am going to...
View Article1.8.0 traffic analysis - ERL as router and not firewall
greetings, i have an issue with traffic analysis that i can't get to display any data at one site. i have traffic analysis successfully working at many other locations - all of these are running as...
View ArticleBGP - IPv6 no-activate
Hi, I'm using the 1.9.0 version with a EdgeRouter Pro 8 to establish some sessions bgp ipv6, but one of them is not working. After trying to use the "no-activate" without success, I decided to remove...
View ArticleRe: Site-to-site IPsec VPN remote router GUI won't load
It's caused by IPsec crypto offload at the remote site. I'm using an ER-X running 1.9.0 at both sites. If i disable crypto offload at the remote site, I can access the GUI at the remote site, but if...
View ArticleRe: VPN to LAN
The routes look correct there. You can see where for 192.168.10.0 255.255.255.0 it knows the gateway is 192.168.9.1 . It looks like the machine's IP is 192.168.13.79 so that shouldn't be interfering...
View ArticleRe: ipsec site-to-site tunnel hangs after several minutes no log entry on ERL...
on the edgerouter run sudo swanctl --logand leave it running. This will show a much more detailed log of what is happening. I have successfully set up site-to-site IPsec VPNs from edgerouter to...
View ArticleRe: Edge Router Pro never reboots without hanging on all firmware versions
Any ideas anyone? The issue has gotten worse. I finally got it configured and running, and avoided rebooting it for the past 2 weeks but I had to reboot it today, of course it didn't come back up okay...
View ArticleRe: 1.9.0 Basic Queue Application List Blank
I used basic setup to get me going and then a few tweaks through the UI afterwards. Config below firewall {all-ping enablebroadcast-ping disableipv6-receive-redirects disableipv6-src-route...
View Article