Clik here to view.
Re: Communication between subnets
BranoB wrote:Sorry, I don't have ER-X I can play with now and test this (maybe next week) but looking at the config you're definitely missing DHCP servers for your 192.168.10.1/24 and 192.168.20.1/24...
View Articleadd a route for the cable modem web interface interface
I have an Arris 6190 on ETH0. The default address for the arris is 192.168.100.1. ETH0 is setup to as DHCP, so it can get its address from my provider (Comcast). I want/need to access the Web UI for...
View ArticleRe: Create nat rule to route traffic from eth1 to vtun0
Not sure what to do now. I don't have a clear understanding.I have one isp.My gui is accessed at 192.168.2.1 I want one computer (currently 192.168.2.10 -static to go to the vpn (PIA). It has other...
View ArticleRe: add a route for the cable modem web interface interface
https://community.ubnt.com/t5/EdgeMAX/How-to-access-modem-on-the-WAN-side/td-p/1511558 Regards,
View ArticleRe: Communication between subnets
On your picture above, where it says Address from the drop-down select "Use DHCP" and save.The router should now pull IP from the modem. Modem should be in bridge mode.
View ArticleRe: Communication between subnets
BranoB wrote:On your picture above, where it says Address from the drop-down select "Use DHCP" and save.The router should now pull IP from the modem. Modem should be in bridge mode.Sweet! Now we're...
View ArticleRe: Site-to-site IPSec broke when upgrading to 1.9
I have come to the same conclusion that upgrading to 1.9 breaks site-to-site connection when using FQDN. I do not have a static IP at two of my locations so for now, I will be sticking with 1.8.5. Has...
View ArticleRe: Communication between subnets
If you're getting 10.0.0.x from ISP modem that means the modem is not in bridge mode. Suggest you switch it to brige mode otherwise you'll ne double NATing you connection.
View ArticleRe: Wifi Utilization at Small School
We tested the minRSSI feature last year and it did not go over well. Even when we turned it to a very low level for the minimum level reqiured to maintain a connection to a specific AP we had devices...
View ArticleRe: Wifi Utilization at Small School
We are using HT20 on 2.4 GHz and HT40 on 5 GHz The limit is a soft limit which works pretty well but every once in a while I check our controller and I see one of our APs has 23-27 devices connected...
View ArticleRe: Wifi Utilization at Small School
We tried zero handoff a while back. It brought our network to a grinding halt. Not advised for this kind of environment.
View ArticleClik here to view.
Re: Communication between subnets
BranoB wrote:If you're getting 10.0.0.x from ISP modem that means the modem is not in bridge mode. Suggest you switch it to brige mode otherwise you'll ne double NATing you connection.Yep, I'll test...
View ArticleRe: Wifi Utilization at Small School
Part of the challenge lies in the fact that Apple iPads are unbelivably stubborn about holding on to their signal when connected to one AP and doing EVERYTHING they can to maintain a connection....
View ArticleDoes the ER-X's PoE watchdog ping out the specific interface?
Does the ER-X's (SFP or not) PoE watchdog ping out the specific interface that it's configured on or on the entire subnet that it has access to?
View ArticlePower DSL modem with ER-X PoE?
Does anyone have experience with down converting the ER-X's 24v PoE for a 12v DSL modem? I was thinking of using a simple passive PoE midspan with a DC-DC buck converter.
View ArticleWeb filtering by DPI and Display message to end users for blocked content
Good morning,I have a customer/university where we have deployed EdgeRouter Pro 8 as firewall. So, we have defined the firewall rules as requested by customer, all is working well. Now, the customer...
View ArticleRe: Site-to-site IPSec broke when upgrading to 1.9
Yeah, I'm kind of unsure if i should have marked "not using FQDN" as the solution.Since it actually is a regression from 1.8.5 I have not found a way to solve it without just stopping the use of FQDN...
View ArticleRe: ERL becomes unresponsive after creating basic qos queues
Post your config 1st. Remember, applying lots of QoS rules can take minutes on ERL
View ArticlePush Notifications OSX CalDav server not working.
Have installed a EdgeMax X router with Statt IP because AirPort Extrem eated bandwith with or new 1Gbit/s connetion. We run a OSX Server, only CalDav calender for the moment. CalDave calender works,...
View Article