Re: Enable communication between the two LAN on the same ERLITE 3
I've got a Dual-LAN setup and it works by default routing between the two subnets. LAN - 10.0.0.1/24DMZ - 10.1.1.1/24 On the Routing tab in the GUI, do you see both subnets? If so, you should be...
View ArticleRe: Error Upgrading the System
Hi, thanks for you reply.found another way, SCP to the router then add the firmware from there. Next time I will create a new post. R,--m
View ArticleEdgeMAX - ER3 lite. Dual wan, filter traffic on lan ip, not vlan
Hi forum Is it possible to force traffic from ip lan_01 to use wan_01? And lan_02, lan_03 etc to use wan_02? Im considering making rules based on ips or h/w adresses. 10.0.0.10 -> wan 01, 10.0.0.11...
View Articlemodify dscp : possible completions
Playing around with QoS settings, hitting tab and ? key:admin@fw01# set firewall modify SETDSCP rule 1 modify dscp Possible completions:<0-4294967295> Packet Differentiated Services Codepoint...
View ArticleRe: EdgeMAX - ER3 lite. Dual wan, filter traffic on lan ip, not vlan
Start by looking into these KB articles:PBRLoad-Balance
View ArticleRe: Edgerouter lite using PPPOE will not use WAN IP for Proxy
Thanks for the info on the address group. However I will say the two years I used the Proxy on the WAN interface it was also DHCP. I personally think it has something to do with the PPPOE being a sub...
View ArticleRe: EdgeMAX - ER3 lite. Dual wan, filter traffic on lan ip, not vlan
Ty for your reply. I did see those articles, but they are based on 2 different subnets. Load balancing isnt a 100% perfect match, as I always want traffic from source A to go out on port A. All other...
View ArticleRe: Suggested EdgeRouterX Configuration
Thank you for responding. I have DHCP reservations set for various devices on the network: 192.168.10.90-119. Then, the current router has a DHCP IP Address Range of 191.168.10.120-199. Should this...
View ArticleRe: EdgeMAX - ER3 lite. Dual wan, filter traffic on lan ip, not vlan
PBR is prime component (that's why I mentioned it 1st)Load-Balance KB isn't necessary, but might be useful for bonus stuff like failover-only.
View ArticleRe: Edgerouter lite using PPPOE will not use WAN IP for Proxy
If the proxy won't start when using the PPPoE address......you're sort of stuck with NAT. SInce the proxy isn't on eth1 , this might cause current portmap not to work.Create a manual dNAT rule for the...
View ArticleRe: Time based firewall rules not working
It's always funny reading some of these threads where helpers seem to focus on the wrong thing.I'm glad you found out what was causing the issue. Perhaps a note could be added to the manual about the...
View ArticleRe: EdgeMAX - ER3 lite. Dual wan, filter traffic on lan ip, not vlan
as said, PBR is the way to do it -- you can set it up however you need. Or, you could use VLANs if you want to route based on subnets ...
View ArticleRe: Suggested EdgeRouterX Configuration
The setup you want is entirely possible. Do you happen to have the ER-X already, or are you just asking before you buy? If the former, please post your config. Depending on your current network...
View ArticleEdgeRouter PoE 5 link detection
I have a Arris TM822 Docsis 3 Cable Modem (just bought my new router today). when I plug it in it automatically sets it to a 10/full speed. It should be 1000/full but for some reason it isn't detecting...
View ArticleEdge Router X capability
Good Evening, Noob question here. Thinking of getting an Edge Router X. I need to split my internet access between two properties from the modem: the Residence and the Rental.I want these two...
View ArticleL2tp connection failing
Bought a few ER-X units for some remote site testing and I am working on setting up an L2TP VPN. I followed the instructions and everything committed just fine but the VPN on Windows 10 will not...
View ArticleRe: DNS Forwarding
I checked my dnsmasq.log and here is what comes up ; its really filling up and looks like its restarting periodically: Sep 2 15:22:40 dnsmasq[3347]: started, version 2.76-1-ubnt2 cachesize 150 Sep 2...
View ArticleTeredo tunnel issue in Windows
I use the Xbox app that's built into Windows 10 to stream my Xbox One to my Windows laptop. With the Edge Router X v1.9, I'm getting a message that Teredo is not functioning (pointing me to this link)....
View ArticleRe: 2 networks in one link EPR6
I didn't look the original thread before I posted it, It's a mess, jeje, I'll clean it later, I finally find a way to do what I need HERE and for adding the VLANs to the bridges, I didn't find in the...
View Article
