Re: EdgePoint R8
Unfortunately what you're missing is the EP-R8 is a router, not a switch. If you want a switch you needed the S16 instead. The R8 is designed to support a different IP network on each interface,...
View ArticleRe: Cannot access Internet from VLAN
Hey , many thanks for your answer. Really helpfull for me. ivan
View ArticleRe: IGMP forwarding accross bridge interface sourced from vlan interface
The solution was: sudo su -echo 1 > /sys/devices/virtual/net/brx/bridge/multicast_querierbrx was br1 in my case. To make it permanent: vi /etc/rc.localadd the echo line before the exit 0. My mistake...
View ArticleRe: Private Internet Access - Routing/NAT Help
I can see some traffic going from my VPN IP to some other public IPs. It appears the interface vtun0 is going down after only a small amount of packets are sent: tcpdump: pcap_loop: The interface went...
View ArticleRe: Cannot access Internet from VLAN
guys... one small additional question regarding to VLAN_LOCAL. As I mentioned I need to create rule to block access from VLAN to router - that's fine and now I know how to do it and it's working...
View ArticleRe: Edgerouter Lite DUAL wan issue
Thanks both of you, I was able to get inter-VLAN routing working properly with the steps you provided.
View ArticleRe: Cannot access Internet from VLAN
Nope vlan_local should look like this: default droprule 1 accept destination udp port 67rule 2 accept destination udp port 53 (edit -- order doesn't really matter here though) Don't apply it to your...
View ArticleRe: Cannot access Internet from VLAN
Read my message again carefully. I stated: default droprule 1 accept protocol udp port 67,53 That's it.
View ArticleRe: EdgeMax - forward HTTP to Squid
It's getting strange!!! When I call a website with my setup from a client which is diverted to the proxy, I can see the entry in the SNAT (command: show nat translations detail) for this access to this...
View ArticleRe: EdgeRouter-X IPv6 on Comcast BCI
Ok so this should be good then right? dhcpv6-pd { no-dns pd 0 { interface switch0 { host-address ::1 prefix-id :1...
View ArticleRe: EdgeRouter-X IPv6 on Comcast BCI
Also I guess I'm not yet familure with the ubnt command line. Whats the easiest way to add the config lines?
View ArticleDual WAN, dynamic IP. 'web check' only work on primary interface
EdgeOS 1.9.0 on ERL. I have dynamic IP updating enabled on my dual-WAN setup. The first IP is fine and updates correctly however due to my topology I cannot get the second to update correctly. The...
View ArticleGRE and/or VPN IPsec is only handling HTTP/HTTPS
I've just begun setting up my device for the first time and have established successful VPN IPsec and GRE tunnels separately to my destination, however, only HTTP/HTTPS traffic is traversing either...
View ArticleERPOE-5 with two RocketM5 and Unifi APs, same subnet
Hello, I finally had some time to take a deep dive on the ERPOE-5 and have been able to simplify my network a bit. But I'm having some trouble integrating a second AP covering the same subnet. eth0:...
View ArticleRe: ERPOE-5 with two RocketM5 and Unifi APs, same subnet
I should add that when the UAP-AC-LR is connected to the ERPOE-5 eth3, I can see it in the Unifi Controller but it has IP address 192.168.1.20. I can reboot it from the controller, set a static IP, or...
View ArticleRe: Cannot access Internet from VLAN
OK guys .. I see now ... . The last control question.. . the rule: - rule 1, default accept, established/related, all protocols should be only in VLAN 10, 20, 30 or is necessary apply this rule to _IN...
View ArticleRe: Cannot access Internet from VLAN
centrumsigord wrote:OK guys .. I see now ... . The last control question.. . the rule: - rule 1, default accept, established/related, all protocols should be only in VLAN 10, 20, 30 or is necessary...
View ArticleRe: NetFlow using nfacctd
Finally figure it out and it's a dumb one...my IPTABLES firewall was blocking the traffic. Changed the ruled to allow port 2055 inbound and nfcapd works just fine. Learned an important lesson: tcpdump...
View Article