Re: EdgeRouter to ToughSwitch Trunk and Network Design
I am allocated two public static IPs. I have only been using one. The only way I have been able to use both is by placing a switch before Eth0 and assigning accordingly... though I have not tried...
View ArticleRe: ipv6 Tests Fail -- EdgeOS Firmware v1.9.0
And that link-local address for the default route is definately your WAN router's address? Nothing else running router adverts on that segment? Can you ping or traceroute from the ERL itself?
View ArticleRe: how to setup my wireless APs
Also, I believe you'll want to plug the cable from the ERL to the Linksys into a LAN port, not the WAN port (unless the Linksys supports some sort of bridge mode that disables the firewall on its WAN...
View ArticleRe: ipv6 Tests Fail -- EdgeOS Firmware v1.9.0
AndyWrightUK wrote:And that link-local address for the default route is definately your WAN router's address? Nothing else running router adverts on that segment? Can you ping or traceroute from the...
View ArticleRe: ER-PoE - Chromecast between subnets, wireless client to wired host
MindTooth wrote:... But last hurdle is the Chromecast one. ...https://productforums.google.com/forum/#!topic/chromecast/ZGm4p8VcpAU What's the issue?
View ArticleRe: DNAT rule not working - 5 static address block from ISP
I removed the port 69 from Source and left 69 in the translation. I'm not 100% sure (without being in front of the phone I am remotely resetting to force to pull the config) but my count is not...
View ArticleRe: ipv6 Tests Fail -- EdgeOS Firmware v1.9.0
You're running a PD client which will automatically configure radvd on your vif interfaces - your posted config looked ok in that respect. I'd remove any manual ra configs as they'll fight with the PD...
View ArticleRe: DNAT rule not working - 5 static address block from ISP
You would think that even if the entire logo fetch did not work, you would still at least see the DNAT rule count increase. Have you tried with something other than one of the phones like a tftp client...
View ArticleRe: Disabled interfaces enables itself after some time
Hi, It took a few hours until it falled back to this disEnabled state. I've attached a screeshot and the output as requested: r00t@Router:~$ show interfaces ethernet eth1 eth1:...
View ArticleRe: ER-X - Corrupt downloads
16again wrote: Seems to me like the ER-X recalculates the checksum using the corrupt data.As I understand, this was exactly root cause of the ER-L corrupt downloads issue. There offload engine was...
View ArticleRe: Help getting OpenVPN (Client to PIA) to come up
linkd22 wrote:So im not sure if that was the exact fix because I changed some other stuff while browsing the forums for help, but the tunnel is now UP. However, my new issue is that PIA sends a...
View ArticleRe: Edge Router X Automatic WAN failover not working
Doing the commands and setting it up that way worked. It makes sense as well why it would work. Thanks
View ArticleClik here to view.
Re: how to setup my wireless APs
smax wrote:Also, I believe you'll want to plug the cable from the ERL to the Linksys into a LAN port, not the WAN port (unless the Linksys supports some sort of bridge mode that disables the firewall...
View ArticleRe: ipv6 Tests Fail -- EdgeOS Firmware v1.9.0
AndyWrightUK wrote:I'd remove any manual ra configs as they'll fight with the PD (and reboot the erl as sometimes changes don't seem to fully take effect). Given that you can ping from the erl I'd move...
View ArticleRe: ER-X L2TP slow connection
Quick update. Disabling IPSec offload corrected the problem for my devices running iOS, but the problem is still there on my Windows 10 laptop. I'm able to connect through the VPN, but there are weird...
View ArticleRe: ERLite - Auto Restart VPN
UBNT-stig wrote:There is also "reset openvpn client <>"This command is only supported by OpenVPN in server mode only.I have a client:interfaces { openvpn vtun0 { config-file...
View ArticleRe: ERLite - Auto Restart VPN
UBNT-Fenng wrote:This command will restart open vpn.sudo /etc/init.d/openvpn restartBut, it maybe lost the configuration of the openvpn.Unfortunately this command will not restart a client defined in...
View ArticleRe: Can't get OpenDNS to work on my EdgeRouter Lite
That NAT rule should absolutely be working...unless you have IPv6 in your home and clients are preferring the IPv6 DNS address to the IPv4 one. What is the output of: sudo iptables -t nat -L PREROUTING...
View Article