Re: Problem configuring edgerouter lite as DHCP
goldlineIT wrote:set up a static route for 192.168.1.0/24 out your ethernet portThat actually doesn't work (or at least, I could never get it to work) because a lot of cable modems/ADSL modems will...
View ArticleRe: A better way to manage dhcp server options for phones?
It is easy within the actual dhcpd.conf file, it is just that Vyatta and EdgeMax don't support it.My preference for avoiding VLANs is that a few computers end up being plugged into the phone's switch...
View ArticleRe: EdgeRouter PoE 5 seems to be bricked! Kernel Panic at boot after EMRK....
That was it. I guess the warranty is over (my router is 2 years old). Because I need my router asap, I've decided to open it. I've found an 4 GB USB stick (HP 125w) in my desk drawer, so I've replaced...
View ArticleRe: DHCP leases aren't shown for vlan eth1
I'm running an ERL, currently with 4 different DHCP servers on 1.9.0
View ArticleRe: DHCP leases aren't shown for vlan eth1
I've had an issue where my DHCP ranges had to coincide with my vlan ID, so for my vlan 100, I needed to use 10.0.100.x, and for vlan 200, I needed 10.0.200.x
View ArticleRe: limit downstream traffic by limiting upstream traffic
On a case-by-case basis, yes it can be done (and it's fine). The trouble comes in when you're trying to set this across an entire network -- not only will you impact the downstream traffic, but any...
View ArticleLighttpd restore after corrupting.
I believe I somehow botched my Lighttpd setup in my ER-Pro. I still have SSH access, but the Web GUI is no longer showing up anywhere. It all started when I tried to use an old script to get lets...
View ArticleRe: Not getting any firewall messages in logs
I literally cannot compare one snippet of a config that "is working" to another that "is not" when they don't show anything that can actually be compared. Yes, the two rules are the same on the...
View ArticleRe: how to apply a firewall modify to a VLAN interface?
huh, could've sworn they had a section on working with vlans in the CLI in the manual i linked... at the very least it does indicate one can use tab-completion while writing commands to see what...
View ArticleRe: GUI Cant Show Advanced QOS Rules on Edgerouter X
I'm experiencing the same problem. I can initially configure it in the GUI but once I log out then log in again I can't see the configuration. The confiugration is still present and can be seen on the...
View ArticleRe: limit downstream traffic by limiting upstream traffic
I'm aware that this would affect all upstream and thus downstream traffic. The alternative is having 90+% packet loss on some UDP connections and not being able to make phone calls. I have only one...
View ArticleFULL BOGON list HELP
Hey guys, I am trying to implement and block full bogon lists. the problem I am currently having is that adding the full ipv6 list fills the firewall group up before it finishes. I believe the exact...
View ArticleRe: GUI Cant Show Advanced QOS Rules on Edgerouter X
You need to click exactly on the dots to show the config.
View ArticleRe: GUI Cant Show Advanced QOS Rules on Edgerouter X
I mean, look at my picture, click exactly on the yellow dot.
View ArticleRe: GUI Cant Show Advanced QOS Rules on Edgerouter X
Thank you that did it. It would be nice to have an option to expand everything without clicking so many times.
View ArticleRe: Can't load some pages Edge Router ER-Pro
can you ping "192.30.253.112" which is github.com?can you go to the website "192.30.253.112"? It doesn't look like you have any DNS servers set up so maybe that is part of it?
View ArticleRe: EdgeRouter X problem connecting to Internet.
Is it a static IP or DHCP from the ONT? - The Zyxel was configured to static IP, the Edgerouter to Dynamic - I will try configure the Edgerouter to static as well. Does it need authentication for PPPoE...
View Article