QOS Advanced Queue Exmple?
I'm trying to figure out how to use the QOS Advanced Queue and am having trouble finding many examples. I was wondering if anyone knows how to do it and we could come up with some simple examples here...
View ArticleIs this a viable configuration - ER Poe5
I currently have my ER PoE-5 setup like this: eth0 - ISPeth1 - nothingeth2-4 setup as switch for my local lan with:--eth2 - connected to 8 port switch #1--eth3 - PoE enabled to AP--eth4 - connected to...
View ArticleRe: Multiple subnets
I don't know what a PVID is. Reading the FAQ didn't really help in understanding how it work and what it does. It seems to use multiple physical ports and vlans?
View ArticleRe: Multiple subnets
You kinda seem to be in way over your head here ... if this is a business, you may be better off hiring a consultant to get things done properly.
View ArticleRe: edgemax edgerouter POE eth1 MIA
Thanks for the reply. I checked by /config/config.boot interfaces section and it does have an eth1 definition. I've attached a copy of the interfaces section. Do you see anything that looks weird...
View ArticleRe: Multicast, Sonos, Phorus & Play-Fi Broadcast 255.255.255.255: Discovery...
Correct, I compiled the binary for the mips64 big endian byte order CPU architecture, whereas the ER-X uses mips64el, which is little endian, so it cannot run without errors. You will actually need a...
View ArticleRe: Multiple subnets
This is for private home use. I am trying to learn by doing but nothing makes sense/clicks yet. Many terms throw me off as I cant seem to pin point what belongs where and how yet. For example I am...
View ArticleRe: Commit fails when setting up zone-based firewall - router no longer...
Edited firewall config post above to make it easier to read. Also realized I forgot to recreate a WAN_TO_DMZ rule allowing all traffic into the DMZ zone (that's the whole point after all). Firewall...
View ArticleRe: Is this a viable configuration - ER Poe5
sure, it's perfectly fine. There are a couple of ways to go about setting everything up. Here's how I'd do it.NOTE - I am assuming you have a relatively recent controller version (4.x or 5.x) EXISTING...
View ArticleRe: Is this a viable configuration - ER Poe5
Thanks for the detailed explanation. I had planned to do that all, just wasn't sure if my idea of using eth1 as a separate subnet would work. I am new to the ubnt product so I am learning a bit as I...
View ArticleRe: Frequent Disconnections with EdgeRouter
Did you try swapping out the cable between the router and Netgear switch? The Ubiquity ERX(-SFP) works well in switch mode, and is configurable as vlan aware..
View ArticleRe: IPsec Route vs Static Route priority
Thanks for the reply, but unless I'm missing something the thread you linked and others with similar titles all pretty much lead back to the same conclusion that something is wrong with how the routing...
View ArticleRe: Frequent Disconnections with EdgeRouter
I'll try a different cable, but I doubt that's the issue since it seems to work fine with my laptop on the same cable. Good call on the ERX, somehow I didn't think of that as a switch, lol.
View ArticleRe: Multiple subnets
Okay, I was going between "consumer" and "newb who got thrown in the deep end" ... PVID = Port Virtual ID. This helped me wrap my head around VLANs Scenario: You have three physical networks, red,...
View ArticleRe: Frequent Disconnections with EdgeRouter
tocirahl wrote:Doesn't seem like the router is rebooting, and best I can tell the same configuration works fine with 1 laptop connected to the router with no switch. Makes me suspect that it's probably...
View ArticleRe: Frequent Disconnections with EdgeRouter
I also see that the Netgear GS108Ev3 is on sale for $18 right...
View ArticleRe: EdgeRouter - WAN Failover configurations
I resolved #1 by:# show firewall groupnetwork-group 3G_MODEM {description "3G Modem Netowkrs"network 192.168.8.0/24}# show firewall modifymodify WAN_FAILOVER_POLICY {rule 10 {action modifydestination...
View ArticleRe: Multiple subnets
If I understand it correctly (I actually have colored cables) I would need a managed switch instead of an unmanaged switch (from tp-sg1016de to tp-sg1005d where the tp-sg10005d is a unmanaged) in order...
View ArticleRe: EdgeRouter X - vlan existing guess network for IOT
I'm not clear on what you're asking. What do you mean by adding and ERX to "secure the Asus's guest network"? Why/how is the Asus guest network insecure? Can you connect betweek your existing guest and...
View ArticleRe: Multiple subnets
Well, you "can" use unmanaged switches downstream of a managed switch, provided that all hosts on that unmanaged switch are going to be on the same VLAN.
View Article