Quantcast
Channel: All EdgeRouter posts
Browsing all 60861 articles
Browse latest View live

Re: Which router for gigabit fiber?

Then I guess the autoneg issue is only intermittent for some ports. On my end, it was permanent - perhaps they're using not 100% the same equipment on all COs. Which CO are you on? I'm on 780WUE...

View Article



Re: EdgeRouter setup for Swiss FTTH providers

You can directly use the router. For the registration, swisscom ask a serial on the bill or on customer aera. I prefer spoofing my mac address because I can change equipment without register again.

View Article

Re: EdgeRouter setup for Swiss FTTH providers

Ahh.. so they register your MAC during registration? Good to know.

View Article

Re: Which router for gigabit fiber?

I'm on 790WID. Do you think I should ask them to disable autonegotiation? Edit:Good idea, will run tcpdump when I have the chance to. The last time I only checked the logs but didn't find anything...

View Article

Re: Which router for gigabit fiber?

My friend had/has autoneg enabled and never had a problem beside loosing ipv4 but not ipv6 over the weekend. Maybe there are multiple problems... Not sure what fixed it? He power cycled the device. But...

View Article


Re: EdgeRouter setup for Swiss FTTH providers

I think yes

View Article

Re: Routing locally originated traffic after failover in 1.9.0

I have lb-local set to enable, but locally generated traffic doesn't follow the load-balance rules, and instead uses the main routing tables. The problem with setting distances on the main routing...

View Article

Re: Which router for gigabit fiber?

Well, if IPv6 remained up, it's definitely not the same issue.. in my case, I had zero connectivity and the port on the remote end was down. It's time to inquire if they ever reproduced that issue...

View Article


Re: EdgeRouter setup for Swiss FTTH providers

Ahh I see, so my access is based on registration to one router (MAC address in this case). That would make sense as to why I can't get past the gateway. Thanks for sharing that info, I like the idea...

View Article


Re: Disable eth1 via SSH

It's an EdgeRouter 5-Poe. -https://www.ubnt.com/edgemax/edgerouter-poe/

View Article

Re: Which router for gigabit fiber?

@humbaAre you sure you got global scoped Ipv6 addresses on eth5 and switch0? Check out the config I posted yesterday. Works for my friend with that dhcp-pd and firewall config. As I said, I'm not sure...

View Article

Re: EdgeRouter setup for Swiss FTTH providers

set interfaces ethernet eth5 mac 00:00:00:00:00:00

View Article

Re: Which router for gigabit fiber?

Worth mentioning: I used to have a TP-LINK MC220L with the same SFP module (TP-LINKTL-SM321B) for a couple of weeks. During this time I didn't have any problems. 

View Article


Re: EdgeRouter setup for Swiss FTTH providers

 Excellent, Thanks! I'll give it a shot this evening and provide feedback on the results.

View Article

Re: Need help winning the UBNT vs PFSense vs Sonicwall debate

Firewall throughput is offloaded.  Even IPSEC can be offloaded.Openvpn however isn't For non-offloaded stuff pfsense, being x86 powered , has larger throughput.  But this requires hardware or...

View Article


Re: EdgeMax Router + AirFiber + Cisco Switch

I would have the /30 in a completely separate netblock. e.g. if sites a/b/c are 192.168.[1|2|3].0/24, use 192.168.0.[0|4]/30 for the AB/BC AF networks. Run these directly on the site a/b/c routers (and...

View Article

Re: internet speed issues

That's not the full config, so we can't tell you what's missing... though since it's an ER-X, check if "hwnat" offload is enabled.  If not, enable it. This command should do it for you:set system...

View Article


Re: CLI Integrated dnsmasq Adblocking & Blacklisting v3.5.5 Easy Config

New domains to block:set service dns forwarding blacklist domains include themillionaireinpjs.com set service dns forwarding blacklist domains include wwwpromoter.com set service dns forwarding...

View Article

Re: Need help winning the UBNT vs PFSense vs Sonicwall debate

Performance would, however, get a bump from an ER-8.  Might even see a bump on an ER-X (although they are a bit resource-starved if you're needing more than a few users).

View Article

Re: Disable eth1 via SSH

set interfaces ethernet eth1 disable Should take care of it for you once you've committed the change.

View Article
Browsing all 60861 articles
Browse latest View live




Latest Images