Re: Not getting local DNS to work properly
Out of curiosity, what are the contents of /etc/dnsmasq.conf?
View ArticleRe: Not getting local DNS to work properly
The /etc/hosts looks like this: 127.0.0.1 localhost# The following lines are desirable for IPv6 capable hosts::1 ip6-localhost ip6-loopbackfe00::0 ip6-localnetff00::0 ip6-mcastprefixff02::1...
View ArticleRe: EdgeMax Routing Advise
BranoB wrote:Don't use WAN port on ASUS, connect it to ER-X via LAN port only.ASUS will act as AP and switch only. Disable DHCP server on ASUS. This will simplify your setup, all network routing,...
View ArticleRe: Not getting local DNS to work properly
gfunkdave wrote:Out of curiosity, what are the contents of /etc/dnsmasq.conf?## autogenerated by vyatta-dns-forwarding.pl on Fri Jul 8 17:42:48 CEST...
View ArticleRe: DNS setup with Windows DNS server
16again wrote:@d-m-zhttps://technet.microsoft.com/en-us/library/dd197552(WS.10).aspxThe DNS Client service queries the DNS servers in the following order: 1. The DNS Client service sends the name query...
View ArticleRe: Not getting local DNS to work properly
At this point, it should just work. I would try removing all the DNS forwarding options and clearing entries from the host file. Then, request a new DHCP lease so it updates the host file. Clear the...
View ArticleRe: Not getting local DNS to work properly
gfunkdave wrote:At this point, it should just work. I would try removing all the DNS forwarding options and clearing entries from the host file. Then, request a new DHCP lease so it updates the host...
View ArticleRe: Not getting local DNS to work properly
static-host-mapping { host-name b3 { inet 192.168.111.2 } }That's your problem there. Either get rid of that, or change it to b3.ikjarl.local. You can add it inside your DHCP service, as a static...
View ArticleRe: erlite3 only ½ pages load
randydrobinson wrote:selecting 'all', just appeared to toggle the (4) available options.Actually selecting "all" (which applies it to all interfaces) is not the same as selecting all four options...
View ArticleRe: Multiple GRE Tunnels (WAN LB) setup to remote site
Thanks for reporting the issue. I just did a quick test and was able to create two tunnel interfaces without the error. Could you provide more details (the "before" config", the exact changes being...
View ArticleRe: ER-X traffic policy error under v1.8.5
Thanks for reporting the issue. Yeah there is a bug with the limiter config in 1.8.5 and I have already fixed it for the next release (alpha testing should start soon). For now one possible workaround...
View ArticleRe: ER-X v1.8.5 & hwnat
gfunkdave: Ah sorry, forgot about the QoS part. Yes 16again is correct, traffic with QoS policy applied will not be offloaded by the HW NAT. Therefore, if QoS policy is applied to all traffic, enabling...
View ArticleRe: Inbound Masquerade for device
Yeah that should be doable with "source NAT" rules (not port forwarding which is destination NAT), e.g., create a source NAT rule with "masquerade" translation, outbound interface set to the LAN...
View ArticleIPsec tunnel up but no traffic after router
Tunnel is up on both ends. Routers can ping each other. The workstation behind the routers can also ping the far router. I can't ping a far workstation on either side from either the router or the...
View ArticleNat Issues
I'm having issues with Nat. I have 2 static public ip addresses. 1.1.1.1 and 2.2.2.2 The wan interface is using 1.1.1.1 as the main ip and 2.2.2.2 as the second ip. My lan is Natted to 1.1.1.1 and...
View ArticleRe: ipv6 Prefix delegation for a other Router (Fritzbox)
Is this patch scheduled to be included? or is the dibbler stuff from https://community.ubnt.com/t5/EdgeMAX-Beta/DHCPv6-PD-Replacement-of-WIDE-DHCPv6-to-Dibbler-or-ISC-DHCPv6/m-p/1614772 prefered?
View ArticleRe: ERX / QoS / SmartQueue - recommendations for 100mb symmetric WAN
I can only reply with my experience, which is this. I have an ERX SFP running on a Comcast 100/20 connection. With QoS off, I get 120/20 pretty regularly. With smart queue on and the bandwidth set to...
View ArticleRe: Multiple IP addresses and NAT
Nope, it won't work either WEB interface or SSH on the secondary address, but i can ping it...
View ArticleRe: Multiple GRE Tunnels (WAN LB) setup to remote site
We were able to get this up by downloading, then modifying config.boot with desired tunnel and uploading to router. Error seems to be in the commit.
View ArticleRe: ERX / QoS / SmartQueue - recommendations for 100mb symmetric WAN
Concerning QoS performance of the different devices, my experience (and testing) is as follows: ER-X: 180+Mbps with Smart-Queue (with approximately 500 flows - using torrents to simulate multiple users...
View Article