Re: How to Replace config.boot file with new modified version on EdgeRouter...
Hi again folks, I would really like to know why my ERPE is going crazy - everytime I have tried to change the config.boot file. I have tried PSCP and WinSCP - but I get a fault where Win10 is...
View ArticleRe: L2TP VPN on ERL: Win7 Clients cannot reconnect to VPN after disconnect
Has this been resolved in newer firmwares? I am still experiancing this problem on my ERL-X with 1.9.0. Android has no problem disconnecting and reconnecting however Win 7 requires "restart vpn"...
View ArticleRe: ER-Pro L2TP - VPN Clients Can't Ping Network After 1.8.0 to 1.9.0 Upgrade
I was able to reproduce same symptoms in lab network - l2tp client (192.168.120.40) was not able to ping remote host (192.168.120.60) when load-balancing is enabled. Found following workaround:Remove...
View ArticleRe: How to Replace config.boot file with new modified version on EdgeRouter...
Nothing will change until after you issue the "commit" command. Is that when things go haywire? If so, it's likely that there's something wrong with your config file -- post it here, and we can take a...
View ArticleRe: How to Replace config.boot file with new modified version on EdgeRouter...
Hi dpurgert, Here is the config.boot file that I would like to apply to the ERPE. The file is a modified version - and there could be some issues that I haven't taken in consideration when modifying...
View ArticleRe: How to Replace config.boot file with new modified version on EdgeRouter...
for starters, you seem to be mixing ACL and zone firewalls -- you can't do that. Also, your DNAT rules appear to be wrong - 152.115.x.x will never be an "inside" address.
View ArticleClik here to view.
Re: Introduction
: All the best to you and the great work that youv'e done! I remember when I got one of the first (public) ERL's after some month's of wait at the end of 2012. One of my colleagues said "are you happy...
View ArticleRe: Setting L2TP VPN
If I use that command, i get this message: L2TP VPN configuration error: The specified interface is not configured for DHCP Because this interface has a static ip address, so I have my ISP router...
View ArticleRe: Feature Request - Updated OpenVPN
UBNT-cmb wrote:robokaren wrote:Updated OpenVPN with hardware acceleration for AES would be so fantastic.Hardware acceleration can't help much if at all with OpenVPN. Its primary overhead is in tun/tap,...
View ArticleRe: ER-Poe5 ipsec hardware offload not working
Do you see any other feature I am using that could lead to hw-offload dosent work?
View ArticleRe: Tagging untagged traffic on switch0 to a VLAN and vv
We will have to see about adding this functionality to the ER-PoE. It most likely won't be added in the near future. The ER-X might make a small, inexpensive managed switch since it already has this...
View ArticleRe: Setting L2TP VPN
With double NAT you'll need to mitigate using a setup like described in this post here.
View ArticleERPro-8 issues with NAT and/or Bridging
Hi, Hope you can help me with this as I've done many atempts to solve it but oviously I haven't got into the solution yet. The situation is that currently I have an ERPro-8 in a datacenter which has...
View ArticleFailover WAN routed IP
We run a WISP that routes public IP's over our 10.0.0.0/19 network. All radios are in bridged mode and we terminate the customer with a 8 port EdgeMAX router. eth0 is connected to the 10.0.0.0/19...
View ArticleRe: Smart Queue throughput
Thanks. I'm wondering what would happewn if multiple fq_codel shaped queues were somehow rate-limited at the aggregation point. Would the feeding shapers react to the congestion, as fq_codel on those...
View ArticleRe: Multiple ip address on same WAN interface with dhcp
You can use pseudo interfaces, to get more DHCP addresses on a single interface:Link
View ArticleRe: ERPro-8 issues with NAT and/or Bridging
Can't you use a routing protocol instead of HSRP?
View ArticleRe: EdgeSwitch to EdgeRouterX via SFP
We had great comms 1ms at the beginning and not a lot of data traffic. But after a few hours, its like the comm ports loaded up and acted like a loop was in place. But it was just a bridge to an...
View Article