Re: Blocking Internet access of host on WAN_OUT or LAN_IN
if you had multiple subnets that you were connected to and you wanted to block internet access to one computer but not access to the other subnets, you would then have to specify that the internet is...
View ArticleRe: Comcast dscp and VOIP QOS
i have the comcast smc business gateway, which i am sadly required to have because i have more than 1 ip address.
View ArticleRe: MS PPTP client to far end PPTP server connects, but is very slow
Definitely still in the same boat. PPTP is virtually unusable for me now. I will try offload changes next to see if that has any effect. Here is my latest config with the NAT rules removed. firewall {...
View ArticleRe: Comcast dscp and VOIP QOS
camper8080 wrote: What I'm curious about is if changing DSCP from CS1 to CS0 on the LAN side will actually help. As goldlineIT found, it does effect Wi-Fi since it has it's own QOS/WMM. It should not...
View ArticleRe: DNS: resolv.conf not sync'd to hosts?
Will need the full dns forwarding set up (apologies for not asking earlier). Please give us the output of show service dns forwarding By the way, your system dns (the dns that ERL is using - will see...
View ArticleRe: Comcast dscp and VOIP QOS
craign wrote:i have the comcast smc business gateway, which i am sadly required to have because i have more than 1 ip address.Interesting, why is it required?
View ArticleRe: Comcast dscp and VOIP QOS
if you have multiple static ip addresses, you have to use their modem. i've asked, i've called level 2 tech support directly (don't ask what i had to do to get that number) and they said that it is the...
View ArticleRe: Secure guest VLAN and allow guest portal to main LAN
Yes it will do, my mistake! I'll try moving the main lan to another vlan and see where that goes.
View ArticleRe: TDS IPTV with EdgeRouter Lite
Thanks for these directions! Got it working once I figured out a couple details I missed in step 4-5 about the default action to Accept instead of drop for the rule set... Something I'd note to others...
View Articlenetwork share between ETH1 and ETH2
is it possible to connect a network share in different subnetETH0 = WANETH1 = LAN1 192.168.99.0/24ETH2 = LAN2 192.168.100.0/24 Connect from 192.168.100.38 to \\192.168.99.38\share net use ends wit...
View ArticleRe: DNS: resolv.conf not sync'd to hosts?
That's my intent... that the ERL uses itself (including as a DNS cache), falling back to the external DNS when the entry is not in the cache.tcat@ubnt# show service dns forwarding cache-size 150...
View ArticleRe: network share between ETH1 and ETH2
yes it is possible and should work. Why are you using net use? Have you tried opening windows explorer and typing \\192.168.99.38\share?
View Article100% CPU usage 1.9.1 and UCRM
Im using an ERpoe with firmware 1.9.1 I was troubleshooting where my router was always in 100% cpu usage....it was slow to load the GUI and access my cable modems GUIs aswell. slow to the point of...
View ArticleRe: SCP not working but SSH session are OK
The checksum is wrong on the receiving end. Something has smashed some packets on the way. Changing the MTU was a good idea. Too bad it didn't work. Is Path MTU Discovery (PMTUD) broken somehow? Are...
View ArticleRe: OSPF: One Edgerouter insists itself is the DR, even though it isn't
I'd capture OSPF packets on both routers and check the details.
View ArticleRe: EdgerouterX
How can I setup IPsec VPN site to site using 0.0.0.0/0 as remote prefix using v1.8 and above..I tried but it bricked my router.
View Article