Re: EdgeMAX EdgeRouter software version v1.9.1 has been released!
IPSec site-to-site with FQDN and NAT hairpin still appear broken in this release.
View ArticleER-X and WAN Failover behaviors
Hello, I was donated an ER-X, now running 1.9.0 from a client and got to playing with it and had some questions regarding the WAN failover configuration and behaviors. My lab use-case is Eth0 being a...
View ArticleRe: Possible Bug in DHCP Relay
For my config to work I had to add the base interface into the DHCP relay settings, I did read on another post (cant find at presetn) that all interfaces that participate in the relay need to be set,...
View ArticleRe: EdgeRouter X segmentation
Actually, you could do the same even with using the physical interfaces of the router, if all your cables terminate (more or less) to the same place, then you could also use dumb switches .... if you...
View ArticleRe: ER-X and WAN Failover behaviors
Did you already look into:https://help.ubnt.com/hc/en-us/articles/205145990-EdgeMAX-Dual-WAN-Load-Balance-FeatureIt might answer most of your questions
View ArticleRe: Some questions
For 5 users, ER-X might be better choice than older ER3 (=ERL)...unless you do have full figabit linkspeed. DHCP relay might work on VTI mode IPSEC tunnel
View ArticleRe: Name resolution across OpenVPN
On macOS I think I solved the issue: - configure tunnelblick not to update DNS servers- add up.sh and down.sh scripts to the openvpn configuration- The up.sh script ( based on the one found there[1] )...
View ArticleRe: Questions on ERPro-8 remote configuration
Hi Logan, that was exactly, what I was looking for !!! Thanks ...
View ArticleRe: EdgeMAX EdgeRouter software version v1.9.1 has been released!
If v1.9.1 has been released, then when will these images be formally posted on the downloads page. I have been maintining an archive going forward and these filenames are unlike the regular downloads...
View ArticleRe: ER PoE - dual WAN, port forward problem
Maybe I am missing something that must be performed on multi-WAN installation in order to allow incomming traffic to work from all WANs...
View ArticleRe: Multicast, Sonos, Phorus & Play-Fi Broadcast 255.255.255.255: Discovery...
F**king Brilliant! apologies for the language, but this was driving me nuts...
View ArticleRe: ER PoE - dual WAN, port forward problem
Use tcpdump to on ER-X interfaces to see where packets do show up.Spoofing might be a problem in dual WAN port map.If a ssh request on WAN1 is replied on WAN2 with WAN1 address as source, your...
View ArticleEdgemax-Lite and poor upload speed
I am on a Comcast 75 down/10 up connection. When I run speed tests, the download speed is fine but the download speed is often limited to about 2Mbps. It may go higher sometimes, but generally, it's...
View ArticleRe: Edgemax-Lite and poor upload speed
You used "download" twice - which is being limited?Jim
View ArticleSNMPv3
Hi, I'm looking to setup SNMPv3 on my Edgerouter Lite for monitoring of my home network on a VM using Op5 monitor. I've seen a few posts regarding setup strings but I'm not at all versed in CLI so a...
View ArticleRe: Edgemax-Lite and poor upload speed
Thanks for pointing this out. I updated the post. Upload speed is limited. Download speed is fine.
View ArticleRe: Edgemax-Lite and poor upload speed
Then in all likelyhood this is a Comcast issue. My Comcast connection varies it's upstream speed anywhere from 25 to 8-9Mb on different days - they put much less emphasis on that part of the system...
View ArticleRe: DDNS and Hairpin NAT
Did some more digging and this has been mentioned before. Too bad it has not been resolved internally by now. This is a link that describes adding a script "dynnat" to the "/config/scripts" directory....
View ArticleSite to Site VPN - established but seems unstable
Hi, I have my site to site VPN connection now working for some weeks between 2 Edgemax (one Lite, one Pro). I have a rsnasphot script running over that connection, so every 4 hours there is something...
View Article
