Re: IPSec tunnels with main site prefix overlapping remote site networks no...
About this question: "4) Will SPD lookup be performed on all packets? Or only on packets matching a kernel route ?" I think it is only packets matching a kernel route.
View ArticleRe: Route not being accepted
coh84 wrote:... this been resolved in 1.9.1? I can't find it listed on the release notesNo, this was not fixed in 1.9.1, it is scheduled for next release.
View ArticleOSPF6 Panic/Crash [v1.7.0]
We have an ER that has crashed twice with the following trace: PANIC !! Something has gone wrong with ospf6_route_table[0x77f00800] table count = 26, real number = 25 DUMP START...
View ArticleRe: How to assign public IP addresses on the ERLite lan port
So just to make sure I am understanding correctly you want to use 4 different WAN(Public) addresses with 1 assigned to your NAS. I may be miss understanding but heres something I have done in the past...
View ArticleRe: MPLS Guidance
Thank you Arthur - is there any reason not to apply the MPLS IP to the eth3 port? I notice these walk throughs are using the loopback interfaces.
View ArticleEdgerouter Load-balancing delete wan route after all path failed
Hello, I use Edgerouter v.1.9.0 I have two WAN, and I want to failover only, not load balance. When both links are down, and after a while, they came up again, the edge is not able to restore...
View ArticleRe: ERPro-8 NSM Boot Error Messages
Thank you for taking the time to research those entries. I appreciate it.
View ArticleEdgeMax + UniFi AP + Multiple VLANs
I just purchased a ERPOE-5 and am having issues setting it up.Here is what I'm trying to do:1. Use eth0 for Internet2. Use eth1 for my primary 192.168.4.0/24 network3. Use eth2 for secondary subnets...
View ArticleRe: EdgeMax + UniFi AP + Multiple VLANs
First off, on the ER POE, only ports eth2,eth3,eth4 are available on the switch0, afaik. Therefore, to set it up how you have it labelled in your drawing, you would need to bridge eth1 and switch0 (or...
View ArticleRe: EdgeMax + UniFi AP + Multiple VLANs
I did what you suggested and it work perfectly. Thank you!If I were to lump all VLANs onto the same link what would the switch address be?
View ArticleRe: ERX SFP looses WAN connectivity sporadically.
Sad that no one has an idea.I've also noticed the problem happens only on workdays, and never on weekend.The biggest problem is that I have to power off the device with power plug to recover. I wander,...
View ArticleRe: Edgerouter Load-balancing delete wan route after all path failed
See KBYour failover group has no ping target configured....so it falls back to using ping.ubnt.com......which is unknown when both WAN links are down for some time. Use static IP addresses instead,...
View ArticleRe: How to assign public IP addresses on the ERLite lan port
For multiple DHCP addresses on WAN port, look into pseudo-ethernet devicehttps://community.ubnt.com/t5/EdgeMAX/EdgeRouter-Pseudo-ethernet-multiple-dhcp-server-with-static/td-p/1108933
View ArticleRe: EdgeRouterX - VLAN Based Routing
Awesome. I'll give that a shot tonight when I get home. That does make sense too. Create the interfaces across the whole device and then assign them to a specific nic. Edit: Also - yes. I can ping...
View ArticleRe: OSPF6 Panic/Crash [v1.7.0]
After some further work, turns out OSPFv6 is totally screwed, I'm unable to keep the ospf6d process running, it dies with the trace above or the following: Assertion `current == route' failed in file...
View ArticleRe: System Log on switch0
Guessing without seeing your config: eth0 is not a member of switch0
View ArticleRe: MPLS Guidance
Disregard my last post - not enough coffee before posting... I will be testing this shortly and will mark your solution as accepted if it goes well - thank you sir.
View ArticleRe: System Log on switch0
eth0 is unchanged, default just for configuration connected to a NIC with fixed IP, no gateway, no DNS.eth1 is WAN.The problem is the log on eht2.eth2 works as LAN (logging is ok) or as LAN switch0...
View Article