Re: How can i set single IP upload download speed ?
Actually in the latest beta version v1.9.0beta1, there is a new "Basic Queue" QoS feature in the Web UI that can make such configuration much simpler, so you could give that a try if you are interested.
View ArticleRe: EdgeOS doesn't check DHCP after an interface change.
Yeah you are right, this is a bug that has been discussed before, basically it applies to most "addressing/interface changes" (that affects the DHCP server config) after the DHCP server is already...
View ArticleRe: ERX not showing switch traffic
mattiL: Actually what you are seeing is sort of the "reverse" of the original issue reported by the OP. The original issue is that when a port, e.g., eth4, is put into "switch mode", the counters for...
View ArticleRe: Routing IPSec VPN client to /22 LAN (remote clients can see /24 address...
Hey - thanks for the tip. Currently the remote VPN server is the default gateway, so clients are using remote WAN IP as their internet IP. I double checked the routing table to be sure...traffic from...
View ArticleRe: EdgeRouter Lite with OpenDNS and vLANS
Sorry I don't know what you mean. The default network that was setup as part of the router setup is configured to use the router as DNS and DHCP for local.
View ArticleRe: Site-to-Site VPN between EdgeRouter Pro 8 and Cisco ASA 5510
Sorry, I am a bit unsure as to how to add these lines from either the GUI or CLI. It would be great to get step-by-step instructions. NOTE: The last time I made GUI changes to the Firewall Policies,...
View ArticleRe: Dual Wan Help! (newbie)
Here's one that'd work for FTP (note, I'm assuming you have dynamic IPs, rather than statics). Setting them for other services is just as simple (just change ports, etc). FIREWALL: rule 10 { action...
View ArticleRe: EdgeRouter X con't connect for more than 30-60 seconds
I'm not declaring victory yet, however, first computer's NIC may be suspect. Going through a full do-over on the fresh computer _may_ have done the trick. Some of the issues did appear on 3 different...
View ArticleRe: OSPF and failover compatibility
Check "show ip ospf neighbor" and "show ip ospf database" on B and C.
View ArticleEdgeRouter PoE5 - Setting up Eth1 and Switch0 to both share WAN (eth0) - New...
Hi,I just got an edgerouter last week and am having trouble setting up the interface for eth1 correctly after hours of combing through posts, guides, etc. Essentially I am trying to have Switch0...
View ArticleRe: EdgeRouter X con't connect for more than 30-60 seconds
Suspecting computer NIC?Had similar issue recently (ER-X picky to which NICs to talk to)The ER-X ran significantly hotter than other unit, at that point I gave up.
View ArticleRe: How to allow ALL VLANs to print to one device?
OK, so it seems that leaving the PVID blank puts it on VLAN 1 (as it's supposed to). That guest VLAN will most likely NOT be able to print to a local printer, since it seems that subnet / ip address...
View ArticleRe: EdgeRouter X SFP - problem with config
because the router will route between ethx and the switch, as it was designed to do...
View ArticleRe: OpenVPN Site-to-Site Routing
wharris623 wrote: ...Now I'm using a EdgeRouter PoE 5-Port as the router, and I've got it configured as an OpenVPN Client doing site-to-site ...Wes What's the interface openvpn config?
View ArticleRe: ERX not showing switch traffic
Expected behaviour then, thank's for the clarification!
View ArticleRe: EdgeRouter X con't connect for more than 30-60 seconds
I strongly recommend always upgrading from CLI. It'll show you the progress and error messages (if any). And you can decide to reboot or not afterwards. To upgrade firmware to 1.8.5 from CLIadd system...
View ArticleRe: OSPF and failover compatibility
Maybe it's obvious to people familiar with OSPF, butx.x.185.157 and 10.3.50.254 are C.192.168.2.1 and y.y.194.114 and 10.3.50.253 are B.10.1.0.253 and 10.2.31.254 are A. On B: clarknova@RTR-Audits:~$...
View ArticleRe: EdgeRouter Lite with OpenDNS and vLANS
Well, if you have a "server" on your regular lan (e.g. nas.yourhome.tld), and you haven't set the hosts file in your router, it will forward to whatever DNS servers you have set on it (likely your...
View ArticleRe: EdgeRouter PoE5 - Setting up Eth1 and Switch0 to both share WAN (eth0) -...
You've got a couple of things wrong .. The interface eth1 shows as a LAN, but you've got it defined as the WAN interface in your traffic controlAlso, your DNS forwarder should be listening on switch0...
View ArticleRe: Hairpin Problem with vlan
thanks for the suggestion made that change, but still the same result. the weird thing is that snat rule doenst increment the count, either before or after that change. maybe it only increments on...
View Article
