Re: ER-X SFP v1.8.5 can't enable "HW NAT" offload
Yeah you can check out previous discussions (e.g., here) for some more information. Basically they provide similar functionality but there are some differences in for example the configurability,...
View ArticleRe: Problems With New Router Install
post your config (if you're using the GUI -> grey bar at the bottom ... save backup config ... attach the resulting *tar.gz file to a post here).
View ArticleRe: Site-to-Site VPN between EdgeRouter Pro 8 and Cisco ASA 5510
Hi The printer on 192.168.2.250 has a gateway of 192.168.2.1 which is associated with LAN interface eth3 (192.168.2.0/24) ~m
View ArticleRe: ER-X SFP v1.8.5 can't enable "HW NAT" offload
Thanks! Looking forward to the next round...
View ArticleRe: VISIO shapes/stencils
These are great. You just won the internet as far as I am concerned.
View ArticleRe: QOS Rule to prevent Windows Update usage all bandwith
We're still running 1.7.0 (partially because I can't backup the config). Running "update dpi signatures" returns "No new signatures available".I'll try and see whether I can setup that DPI filter or...
View ArticleRe: Problems With New Router Install
Here it is (I could not get the web site to allow me to attach the *tar.gz file so I just pasted it in, hope that is OK). firewall { all-ping enable broadcast-ping disable ipv6-receive-redirects...
View ArticleRe: Site-to-Site VPN between EdgeRouter Pro 8 and Cisco ASA 5510
Hi 16again, Below is a snippet of the tcpdump while remote end attempts to telnet to printer 192.168.2.250. You will see there are no recorded instances where 72.13.6.218 is initiating traffic. What...
View ArticleRe: Problems With New Router Install
And the PC (and everything else) is traversing the Netgear box, right?It's not like PC is plugged directly into the ER? There's nothing wrong with your ER config. Could be IP / gateway issues (e.g. if...
View ArticleRe: Problems With New Router Install
Corrext, the PC and everything else (except the second AP) are using the Netgear built in switch.The old router was using the gateway 192.168.0.1I have rebooted everyting, no change.Checking on other...
View ArticleRe: Problems With New Router Install
Check that those netgear boxen aren't still on the 192.168.0.x network. they might be gettin in the way.
View ArticleRoute tee command in IPChains
I found a post where the ipchains route tee command was not implemented back in 1.7 and was too late to be added to 1.8. Does anyone know if tee was implemented in 1.8.5 or will be added in 1.9? It...
View ArticleRe: Keeping GUI logged in on ER
Thanks. If the Chrome password autofill worked, it would make it possible to get back into the interface with just a couple of clicks. That would definitely be appreciated.
View ArticleRe: Problems With New Router Install
Double checked, both are uising 192.168.1.1 as DNS and gateway, both have 192.168.1.X IP addresses.
View ArticleRe: Problems With New Router Install
Okay, from any of your wireless devices, can you ping 192.168.1.1?If yes, can you then ping the ISP gateway (you'll need to check the ER for that info)?If yes, can you then ping 8.8.8.8?
View ArticleRe: Problems With New Router Install
Yes, I got a ping back from all three.I assume this means some sort of DNS issue?
View ArticleRe: Problems With New Router Install
That's what it sounds like. Try setting the router's DNS to 8.8.8.8 and 8.8.4.4 and see if it clears up
View ArticleRe: IPSec traffic policy issue after upgrade from 1.7.0 to 1.8.0(1.8.5 is same)
Same issue reported here: IPSec overlapping prefix thread. 16again and myself post debugging showing exactly what is happening with v1.8.x that worked fine in v1.7 and earlier. It appears that now...
View Article