Re: IpSec S2S working on Firmware 1.85 - broken on 1.90
You didn't post your config, so it's difficult to tell anything. Are you using "local-address any" in the ipsec config? Are you using FQDN peers or IP address? There was a bug in v1.8.5 where...
View ArticleRe: Port forward on new subnet
That was it, added "switch0" as a LAN interface and now it works! Thank you!
View ArticleRe: upnp2 edgerouterX
Ah yes I did forget to mention that I am using 1.9.0 my apologies. I am not great with the CLI, but I will check your solution. It's not a huge deal, but I am receiving moderate NAT on xbox as well as...
View ArticleRe: ERL3 create PPTP Client
In the beta forum is a sticky post with community contributed feature wizards and I seem to recall a pptp client wizard, but have not tried it.
View ArticleRe: EdgeRouter Lite dead after UniFi Controller Update
Sorry i thought I had it under the EdgeMax. Thanks for moving it.I tried 2 different USB stickes. I downloaded and copied it to a 8gb and a 16gb stick, since the 4gb sticks are not big enough. Once...
View ArticleRe: ERL3 create PPTP Client
Any chance you can provide that thread? I couldnt find it? else, is there a step-by-step guide to do it in "Config Tree"?
View ArticleRe: Edge Router POE - cannot enable POE from GUI
Can confirm this is a browser issue. Had the exact same problem on 1.9.0 when using Firefox 48. None of the dynamic whiz-bang stuff was working in Firefox (graphs, port lights and cpu/ram data at the...
View ArticleRe: ERX Unable to load Web Interface
It might be a certificate chain issue. UBNT needs to sign their certificate with a trusted CA in the chain. See...
View ArticleConfiguring 4WAN 1LAN Load Balancing
I am using Edgerouter PoE5, upgraded to ver 1.9. my internet is using pppoe and internet is on vlan. below is my manual configeth0 - WAN1 (primary)eth1 - WAN2 (backup)eht2 - WAN3eth3 - WAN4 eht4 - LAN...
View ArticleRe: Ubnt Edge Router Pro- Need help with setup!!
Hi, I have the same issues here and i post it on forum. because, my internet is using pppoe and internet is on vlan.. how do i set it
View ArticleRe: EdgeRouter X Tag and Untag Ports Layer 2 Traffic
Well, you are routing between your erx's, so the VLAN tagging goes away. You would have to set different IP ranges or tunnels to make it work the way I think you imagine it working. (And firewall...
View ArticleRe: Prevent local DNS going to external DNS
was able to create an entry in the local hosts file on my PC to create a hostname-IP reference, then use SSH to get into the router. Then used the 'delete service dns ..." command to remove that...
View ArticleRe: EdgeRouter X Tag and Untag Ports Layer 2 Traffic
There should literally be no routing at all. Its all layer 2 traffic. I have two sources of untagged traffic(eth1 and eth2), which I want to tag and then trunk(eth4) out from ERX1 via a wireless...
View ArticleRe: ObiTalk VOIP
/quote "When the Obi202 is plugged in the LAN of the ER, I get the problems stated above but when I connect it to the upstream ATT modem/router LAN (ER's WAN) it works perfectly. So I am sure the...
View ArticleRe: IPSEC VPN issues Please Help!!!
It was a windows firewall issue. Thank you so much for the help!!!
View ArticleRe: ObiTalk VOIP
abcd1234, Of course I put the ATT modem/router into bridged mode. ATT calls this DMZplus. Also my OBI202 was working fine behind my old D-Link router that was replaced by the PE. I haven't disabled...
View ArticleRe: ERL3 create PPTP Client
PPTP Client wizard ... you need to sign up for beta forum access.
View ArticleRe: ERL3 Schedule Reboot every Saturday
Here is a startrouter# set system task-scheduler task reboot_on_sunday Possible completions: crontab-spec UNIX crontab specification string executable Executable path and arguments interval Execution...
View ArticleRe: Prevent local DNS going to external DNS
for documentation, found this helpful in explaining what each of the dnsmasq settings mean. It helps in knowing before they are applied (or are relevant)...
View ArticleRe: Please add model number to SNMP mibs
No, this has not been implemented yet. I was looking for a place where to store hw model, but could not find any (not an expert in this area though). Do you guys know if there exists a standart...
View Article
