Re: Firewall settings don't seem to work
You need two separate firewalls - one for LOCAL and one for IN. They need to be bound to your IOT network interface (eth1), not your switch0. See the kb article:...
View ArticleRe: Router available on one interface but not others
Does it do the same thing on other computers you plug in to the network? Seems like a problem with the laptop or its NIC.
View ArticleRe: Firewall settings don't seem to work
Thank you for the reply. I didn't do the exact setup as described in the article, but used it as a basis for a successful configuration. Question: If I'm trying to protect my LAN from the IoT segment,...
View ArticleRe: Configuring 4WAN 1LAN Load Balancing
all-ping enable broadcast-ping disable group { address-group router_ip { address 192.168.1.1 address 192.168.2.1 description "" } network-group PRIVATE_NETS { network 192.168.1.0/24 network...
View ArticleRe: 2 WAN Load Balancing and Shibboleth, oh boy!
You can create PBR (Policy Based Route) for these destinations to go out always via WAN1 and exclude them from LB.
View ArticleRe: Router available on one interface but not others
Post your config. show configuration | no-more
View ArticleRe: Firewall settings don't seem to work
Read through this LINK to understand the firewall directions.
View ArticleRe: Edgerouter Lite - Getting rid of Bell Canada's Homehub2000 ( Internet AND...
Question, are you located either in Ontario or Quebec? Asking because Bell is using PPPoE, not DHCP. If you are using PPPoE, this is the issue. Have a look back at my proposed configuration the part...
View ArticleRe: Edgerouter Lite - Getting rid of Bell Canada's Homehub2000 ( Internet AND...
You don't need that highlighted rule.You need to move your WAN_in and WAN_local rules to pppoe0 interface otherwise you're wide open to internet!
View ArticleRe: Router available on one interface but not others
Sometimes the obvious answer is staring you in the face but you just can't see it. Although a number of other things are wired, none of the other computers I'd used to try accessing the config...
View ArticleClik here to view.
Re: No-IP for DDNS
we're in different timezone. FWIW.. here is the GUI."Web" and "Web-skip" empty. They're for ddclient to get your public IPv4 address. Most services if not all can auto detect these days.
View ArticleHow Can i use My Domain dhcp server with Edgerouter Max
Hi i have a domain server that i would like to use a my dhcp server but am still unable to figure that out could some please shed some light on the same its a local domain server
View ArticleRe: VLAN offload
I just gave the example of RAM to show the difficulty of fully testing. Actually, RAM is the easiest to test, since , by nature, all its element are readily available. On digital logic, lots of...
View ArticleClik here to view.
Re: How Can i use My Domain dhcp server with Edgerouter Max
https://help.ubnt.com/hc/en-us/articles/204962294-EdgeMAX-Set-up-DHCP-relay-on-interfaces
View ArticleRe: How Can i use My Domain dhcp server with Edgerouter Max
Thanks R4V3R another question lets say my server ip is 192.168.100.35should my cl be like this configure edit service dhcp-relay set server 192.168.100.35 set interface eth0 set interface eth1 commit
View ArticleClik here to view.
Re: How Can i use My Domain dhcp server with Edgerouter Max
Well, that really depends.What's your current DHCP server address? Your domain controller's IP address, probably.And in what interfaces of the router you want to enable DHCP relay?Keep in mind that you...
View ArticleRe: WOL inside LAN not possible with Ubiquiti EdgeRouter POE?
Sounds like nothing should be blocking that traffic. etherwake is actually baked into EdgeOS builds so you could try sending the magic packet from the router and see if you get different results:...
View ArticleRe: After update to 1.9 not able to sent email whit macbook's
It is just emailI turned off hwnatConnection is wan - isprouter -edgerouter- MacBook.It dibble nat becous the isp router is not able to bride ;-(
View ArticleRe: How Can i use My Domain dhcp server with Edgerouter Max
M current server ip is 192.168.100.35 and the dns is 192.168.100.1 and i have people that access the server to store data or collectect with the normal router i disbaled the dhcp server and let me...
View Article