Re: EdgeRouter X bridge mode - super noob
wonay wrote:i had no idea i was buying such an advance device. i just get the one with the best rating on amazon ! Ah, the ER-X is so powerful I'd recommend using it further upstream, replacing...
View ArticleRe: looking to setup Dual LAN so LAN1 to WAN LAN2 to WAN
Ggrrrrrrrrr I know Im close. just can't figure it out. why it is only blocking my webserver.
View ArticleRe: EdgeRouter X bridge mode - super noob
Don't forget to 'kudo' and 'accept' melbo's answer. They get kudo points for doing so.
View ArticleClik here to view.
Re: EdgeRouter X bridge mode - super noob
Thanks ! I might try later ! Should I update the bootloader even if I use it only as a switch ? What is the bootloader by the way ? Haha
View ArticleIPSec offload on ERX blocks gre/IPSec site-to-site between dynamic peers with...
Hi, I have been working on setting up gre/IPSec connection between 2 sites both with dynamic IP address with FQDN (DDNS) assigned, based on these posts below. I use ERX with v1.9.0 firmware for both...
View ArticleClik here to view.
Re: Edgemax with Google Fiber and TV
Thanks for the quick answer, Atlantisman. I actually have already pieced together your excellent instructions with others (Steve Jenkins & Bryan Klinger) to successfully get my ER5-POE working for...
View ArticleRe: Communication between subnets
snafu7x7 wrote:There is also a Switch wizard that seems to be what I want. When I choose the 'VLAN Aware' checkboxit gives me a list of all the ports with spots to enter PVID and VID for each. Is it OK...
View ArticleFeature Request: Do simple manufacturer lookup on MAC addresses
Some of my ASUS consumer routers have a feature that I like: When I hover over a MAC address (say in the DHCP table lookup), it does a simple MAC address lookup and tells me the manufacturer's name....
View ArticleI have WAN/LAN1/LAN2 setup cant access my web server from LAN2
I have WAN/LAN1/LAN2 setup cant access my web server from LAN2.I can acces everything from LAN1 but cant access my webserver which is located on LAN1 from LAN2.Web server is attatched to a domain name...
View ArticleRe: I have WAN/LAN1/LAN2 setup cant access my web server from LAN2
firewall {all-ping enablebroadcast-ping disableipv6-receive-redirects disableipv6-src-route disableip-src-route disablelog-martians enablename LAN1_IN {default-action acceptdescription ""rule 1 {action...
View ArticleRe: Disabled interfaces enables itself after some time
No sry.. still not working as it suppose to do. i've tried a few things but no success at all. After i fried my config a few times (console cable ftw xD ) i've switched to eth2 and the error seems to...
View ArticleRe: Communication between subnets
OK got a couple updates: First, putting the cable modem in bridge mode bricked everything somehow. It killed it's wifi as it said it would in the manual, but I also couldn't get it to pass through to...
View ArticleERL3 to ERL3 IPsec WebGui
Hi All Long time reader first time poster. Finally bought 2 ERL3 lastweek after reading so much about it but can't figure out how to use the IPSEC sitetosite VPN. I had 2 home locations currently...
View ArticleClik here to view.
Re: EdgeRouter Pro - Is there a way to log the VPN User connection and...
what would also be nice is when I use show vpn remote-access to be able to see how long they have been logged in? Like Connection Time. Really need something like that for reporting purposes. So I...
View ArticleRe: EdgeRouter X bridge mode - super noob
robokaren wrote:Can I jump in and ask what the advantage of using an ER-X as a simple switch is? Aren't you using a $50 device when a $20 switch from Newegg would be just as good? Or am I missing...
View ArticleRe: Possible to config ERX to only perform QoS?
I've tried adding a smart queue policy to switch0 and then each interface individually but they are ignored.I want to use the ERX for QoS so I can use DPI on my USG. You cannot do both on the USG at...
View ArticleRe: Comcast IPv6 trouble with ER-X
Come to think of it, this is probably the culprit:-protocols { - static { - interface-route6 ::/0 { - next-hop-interface eth0 { - } - } - } -}It is now removed and things work spiffy!
View Article