Re: EdgeMax Lite unable to support more than 1 voip phone
I never had issues keeping all phones at 5060. But this link reports similar issue on Yaelink phones.
View ArticleERL-3: upnp2 no longer working after upgrade from 1.8.5 to 1.9.0
I just upgraded to 1.9.0 and upnp2 no longer works. Before I start, I've made NO configuration changes other then the firmware upgrade. I'm using upnp for exposing my plex media server to the...
View ArticleRe: Site-to-Site VPN between EdgeRouter Pro 8 and Cisco ASA 5510
The 3rd party confirmed they are injecting the tunnel with traffic. For my part, I tried sending ICMP packets but no luck. Okay will do, I was attaching .rtf but kept telling me I exceeded 20,000...
View ArticleClik here to view.
IPv6 Error
I've configured DHCPv6-PD and RA all by myself. The Basic Setup Function under the Wizard tab just won't work for me. After I've enabled IPv6, I'm able to use ping6 and verify my IPv6 connection using...
View ArticleRe: SNMP wiped after 1.8.5 upgrade
hey guys, snmpv3 was wiped during the upgrade to 1.9 as well...
View ArticleRe: 2XERP 1.85 Slow transfer through site-2-site ipsec VPN over 1GIG/1GIG...
What's 12meg? 12MB/s should be reasonable, 12Mb/s not
View ArticleRe: Routing and VPN performance issues
I'd start off ruling out duplex issue.Set the 100Mb/s ports interconnecting the ERs to 100 full duplex.
View ArticleRe: ISP IP Passthrough
Thanks for your reply, I can put my ISP box in bridge mode.This is why I would like to replace your router by.So the edgrouter is not supporting the IP passthrough?
View ArticleRe: Policy based routing help
Currently, it is setup according to their recommended practice for a production environment (transparent bridge mode). The iPrism has two LANs - one for "in" and one for "out". They call it transparent...
View ArticleRe: EdgeMax - forward HTTP to Squid
You should only use PBR , and/or dNAT rules, this doesn't affect source IP so client IP address should be visible in proxy log files.
View ArticleRe: EdgeRouter Pro 8 crashing
lucasjans wrote:I recently noticed my Router is crashing almost daily...So your router was working fine and then one day you noticed that it is constantly crashing:Did you make any config changes...
View ArticleRe: edgeOS 1.8.5 | ribd uses much CPU
jaymehta wrote:Indeed, after upgrading to 1.8.5 we so constat 60%+ CPU usage and top showed ribd to be the culprit. Had to downgrade back to 1.8.0 to get things back to normal.Do you have "bgp...
View ArticleRe: BGP problem
danielburigo wrote:Hi, there is good news about this problem? Version 1.9.0 has fixed this? ??? Thanks.Unfortunately no, BGP performance issue has not been fixed in 1.9.0.
View Articleload balancer 2 WAN issues.
Ok. I upgraded to the latest version 1.8.5 and did the load balance wizard with 2 WAN. So I have two WAN connected and 1 LAN. Went through the wizard and setup everything. Everything seem to be working...
View ArticleRe: Routed IPTV
I see you are using the rfc3442-classless-static-routes option to get an IP and routes for the IPTV VLAN interface. Currently this will not work as expected because EdgeOS is missing a script that is...
View ArticleRe: load balancer 2 WAN issues.
Firstly the latest firmware is not 1.9.0, not 1.8.5! However, I've got 2 WANs load-balanced at firmware 1.9.0 which I set up at 1.8.5 (not via the wizard though) and it always worked perfectly at...
View ArticleNo 1.9.0 on https://www.ubnt.com/download/edgemax
Is the release pulled? or not yet pushed?
View ArticleRe: OpenVPN CA cert not valid
That's why I asked how you created the certificates. Did you use the batch files provided by OpenVPN or did you do it manually? As long as you don't have dozens of client certificates, I'd simply...
View ArticleRe: ER-POE hangs after upgrading to 1.9.0
I rebooted 7-8 times yesterday, all took 15+ minutes. I stopped timing it after the first couple of boots with the console attached.The most annoying part was my UniFi Wifi stopped "working" when the...
View Article