Re: Multiple VLANs on UAP-AC-PRO with Multiple SSIDs and an EdgeRouter Lite....
Yes you do, that is exactly how I set it up. However, as I had been playing with the netgear VLAN capabilities and settings, it never worked... until I did a hard reset of the netgear to factory...
View ArticleRe: DPI Firewall - No Entries for Top-Sites-Adult but fall within...
Note it is also an issue in 1.8.5, not sure about other firmware but to me it seems like a signature issue and not a firmware issue.
View ArticleRe: Multiple VLANs on UAP-AC-PRO with Multiple SSIDs and an EdgeRouter Lite....
Yes its not too difficult at all. I untag my different vlans in the unifi controller and disable specific wifi networks from being applied to one ap over another. For an idea on the edgerouter side...
View ArticleRe: Reduced Throughput on ERL3
TheTCat wrote:Sure. Offloading is enabled by default I believe...On the ERL it is the default configuration, but this is always the first thing to check since HW offloading may actually not be in use....
View ArticleRe: Open VPN networking is working but no internet access
In fact, the more I look at your DNS set up, the more I think it's wrong. You are pushing 192.168.1.1 as a DNS server AND 192.168.1.100. Which one is your correct DNS server? Delete the other one. If...
View ArticleRe: Building a home network with EdgeMax
Thanks for the info. The diagram was really interesting. Can your PC on the management lan access every device on the network? What if you wanted (for example) your Home Automation Controller to...
View ArticleRe: New to Ubiquti - very slow speeds through new ER PoE 5
gfunkdave wrote:Yes, you need a switch if you want to connect more than 3 devices.Pretty much this. But you can leave eth1 as a separate subnet, plug a UC-CK in there, and use it as a L3 controller...
View ArticleRe: gre-bridge offload support?
Ok, the problem is that I don't know what kind of implementation is hidden under the gre-bridge feature...
View ArticleRe: EdgeRouter DMZ VLAN
No, you cannot "switch" between your "WAN" port and a VLAN interface. You will need to route, and likely perform 1:1 NAT between the stuff on VLAN10 and your WAN interface.
View ArticleRe: Building a home network with EdgeMax
RemotecUK wrote:Thanks for the info. The diagram was really interesting. Can your PC on the management lan access every device on the network? What if you wanted (for example) your Home Automation...
View ArticleRe: EdgeRouter DMZ VLAN
With multiple WAN IP addresses, you'll have to use explicit DNAT & Firewall rules.
View ArticleRe: Spoke to Spoke connection
Thanks. Could you provide more details abou the VTI route? Do I need to switch to VTI on all sites or just the central?
View ArticleRe: OpenVPN Client Setup for Private Internet Access - Continuing Config Help
neebski wrote:@karog@goldlineIT Ok, I was able to strip down my old config and get the VPN connected and routing for the selected devices with the address-group. For the life of me I can't figure out...
View ArticleRe: Using spamhaus lists
What is an "address-group"? How do I do this? stiell@ubnt-rtr:~$ set firewall group address-group SPAMHAUS_DROP Invalid command stiell@ubnt-rtr:~$ set firewall name WAN_IN rule 5 source group...
View ArticleRe: EdgeRouter POE Console Refused Serial Connection
That's the only COM port on my machine. (see screenshot).My machine has a physical ethernet port (where an ethernet cable can be plugged in) and 3 physical USB ports. The rollover cable I have is a...
View ArticleTapering Download Speeds, Intermittent Connection Loss
Please forgive me in advance, I work for a start up and I am the poor soul who is in charge of the internet for 30 angry people. We have an ER-8 and 3 UAP-Pros at my office. For months, we have had no...
View ArticleRe: two webserver serving
You got it in the spolier tag but you had already lost the indentation. When you ran the show command, it should have produced indented text. You should perhaps run that again and post that text in the...
View Article
