Re: Can't get traffic on site to site VPN
I have a strong doubt that the route below is correct for what I want... Thanks, 10.1.1.0/24 [1/0] via IP2 (recursive via GW2 inactive via GW1 )This is what I have for all my routes......
View ArticleClik here to view.
ERPOE 8 Post Console Led Grenn OFF
Hi a silly question ...The Erpro 8 has the console port the LED green in ON?I have the ERPOE and ERLITE and have the console port LED GREEN ON... My ERPRO8 have the port console LED green in OFF, Is...
View ArticleRe: 1.8.5 - trouble with interface distribution graphs
Having the same problems using Safari 10.0 (macOS Sierra Beta), but everything is good in Firefox 47.0.1. My guess would be that this is more of a Javascript or frontend bug. Alex
View ArticleRe: ERLite-3 IPSec VPN throughput issues
try set system offload ipsec enableset system offload ipv4 forwarding enable (not directly related to your issue but worth setting)
View ArticleRe: ERPOE 8 Post Console Led Grenn OFF
That's probably normal; the ER-Lite doesn't have a separate Power on LED, like the EdgeRouter Pro 8 does.In the ER-Lite, the Green LED on the Console port indicates power is On.On the EdgeRouter Pro 8,...
View ArticleRe: Slow ipsec troughput with offload enabled
Thanks for the reply. My mikrotik has other tunnels and all of them can do >100Mbps. Mikrotik for sure has their own ipsec implementation, I'm trying to get rid of my mikrotiks with something else...
View ArticleRe: Requests/suggestions for new hardware models
I am going to agree with you, I think my suggestion would be more for the UniFi product line.Although many of the "hardware switch" chips, also support L3 as well as L2 functionality, so if that is...
View ArticleRe: Can't get traffic on site to site VPN
re-reading config, probably unrelated:On eth2 , all settings for vlan1 are under VIF1, but not its modify rule.
View ArticleRe: force load balance back after failover
Thank you! I have those clients having issues in a different subnet, so I will apply the following conntrack ignore rule to see if it solves the problem: set system conntrack ignore rule 10 source...
View ArticleRe: Can't get traffic on site to site VPN
hello , thanks for the note. VLAN 1 is not used at all, I have now removed it. I created it for future usage but have removed it since then to be sure to focus on my current issue of getting traffic...
View ArticleRe: L2TP Incoming Issue
I was as lost as you are. I could connect to the VPN (PPTP, L2TP over IPSEC) from the local network but could not connect while outside over the internet. Here is what I did: Under Firewall/NAT /...
View ArticleRe: force load balance back after failover
Well that didn't help, after applying that config the clients of that subnet were without internet connection, This is the router config: firewall { all-ping enable broadcast-ping disable group {...
View ArticleRe: Can't get traffic on site to site VPN
Still puzzles me how you can have IP address on an interface (=default vlan1 untagged) and have VIF1 (=default vlan1 tagged) at the same time What's the intention of 10.1.1.0/24 route?You manually...
View ArticleRe: edgeOS 1.8.5 | ribd uses much CPU
I'm feeling lazy so I don't want to look up the link, but I'm pretty sure there's a bug in multipath bgp as of either 1.8 or 1.8.5.
View ArticleRe: Can't get traffic on site to site VPN
Ok, i need to repost the entire configs updated because after having read somewhere that some had problème with the two LANs on each side of the VPN too close to ezch other, i changer the LAN on the...
View ArticleRe: Packet loss issues with upstream Cable modem and EdgeRouter Lite 3
Yeah, so I'm back up in the ~10% loss range and this is what my output of sudo conntrack -L says:conntrack v0.9.14 (conntrack-tools): 3585 flow entries have been shown. I can't imagine how broadcasts...
View ArticleRe: ERLite-3 IPSec VPN throughput issues
Thanks for the suggestion, hhth. I forgot to include the following information - as you can see, IPSec offload is enabled. $ show system image The system currently has the following image(s) installed:...
View ArticleER Lite not getting full ISP Bandwidth
I have had this ER running for 6-8 months without issue. I have had TWC for internet and had a 50/5 package and always got 60/7. Recently they upgraded our speeds to 300/25 and that is where the issue...
View ArticleRe: ER Lite not getting full ISP Bandwidth
You have bridging enabled which imposes a penalty. You need to run no software bridging and take the LAN output to a switch to feed other network devices rather than eth 2
View Article