Re: local hostname resolution with dnsmasq in v1.9.1
Turns out the missing ingredient was actuallyset service dns forwarding options expand-hostsWith that, I can lookup statically (non-DHCP) configured hosts as long as they are set up as follows:system...
View ArticleRe: EdgeMax No IPv6 Networking After Upgrade to EdgeOS V1.9.1
Router has IPv6 connectivity. Clients no longer do however.
View ArticleRe: Powering EdgeRouter X and UniFi AP AC LR from a single PoE PSU?
I have a AC-LR and I am looking to buy the EdgeRouter X to replace my existing router. From reading the posts, looks like I can use the PoE PSU that came with the AC-LR to power the Edgerouter X? Is...
View ArticleRe: Unable to upgrade to 1.9.1
Here is the error doing it via CLI Download suceededChecking upgrade image...DonePreparing to upgrade...DoneCopying upgrade image...DoneRemoving old image...Failed to remove old imageadmin@ubnt:~$ If...
View ArticleRe: EdgeMax No IPv6 Networking After Upgrade to EdgeOS V1.9.1
So presumably the clients only have link local address i.e., those starting fe80? As per my the question in the previous post, do you have an IPv6 DHCP server? The 'managed' flag in the IPv6 Router...
View ArticleRe: Problems with L2TP - Client stays connected but can only load limited...
I didn't realize there was a new release. I hope they can fix this as the hw acceleration is from the soc vendor so I wonder if we have to wait for them to patch it. It's kind of an old chip too....
View ArticleRe: Problems with L2TP - Client stays connected but can only load limited...
The name of the board is Mi-Ti, here's one of the pull request to add gerenic SSL offload.. https://github.com/mqmaker/witi-openwrt/commit/1849469d3ffba3f283738f461db1a091985f97ed
View ArticleRe: ERPro-8 xl2tpd problems
We don't have any DHCP Server on our Network - we use fixed addresses.
View ArticleRe: local hostname resolution with dnsmasq in v1.9.1
gfunkdave wrote:Setting the router to use itself as the system nameserver just lets the router resolve local DNS. It won't help clients on the LAN.I misunderstood. Thanks for clarifying.
View ArticleRe: Powering EdgeRouter X and UniFi AP AC LR from a single PoE PSU?
The ER-X set up as you described should work for you. I have heard some people say that the PoE injector may not be able to keep up if you have a lot of wireless clients, but I doubt that will be an...
View ArticleRe: Slow Internet after installing Edge Router POE
Post your configuration, there might be something hiding in there that could cause issues.
View ArticleRe: EdgeMax No IPv6 Networking After Upgrade to EdgeOS V1.9.1
I believe I have the same problem but with an ERPoE. After updating to v1.9.1 from v1.9.0, the connection status page in Windows says "IPv6 Connectivity: No Internet access"
View ArticleRe: Help with SOHO Configuration Setup on Edgerouter X
This won't be the most straightforward setup for someone unfamiliar with Edgerouters, but certainly not impossible if you're willing to play around with things a bit.First off, it isn't possible to...
View ArticleRe: Config: Azure IPSec VPN with BGP (ERL 1.9.0)
Anybody have this working with a USG?I feel like I'm really close to having it working. I can see traffic leaving the vti64 interface. And a lot of ESP packets going out eth0. And a lot coming in. But...
View ArticleRe: EdgeMax No IPv6 Networking After Upgrade to EdgeOS V1.9.1
Can you post your config? And also post show interfaces and show ipv6 route? Also do you see the Router Advertisment daemon running if you run sudo ps aux | grep radvd? Regards
View ArticleDefault route from DSL modem ignored
Hi. I am attempting to use an edgerouter POE-5 on a DSL modem (Comtrend CT-5072T). The modem is configured in one of its "pass-thru" modes, whereby a client connected by ethernet will receive the...
View ArticleRe: Ports usage question
Your throughput on eth4 would be pretty bad in that scenario. There's a penalty for splitting a port off of the switch on the ERPoE-5.Question - what is your current setup and how is your managed...
View ArticleRe: Ports usage question
Current setup.WAN (fiber 1000/100 mbit)->Netgear gs108 first port----------------------2nd port on switch -> WAN port n56u3rd port on switch directly to IPTV boxAll pcs and consoles goes into...
View Article
