Re: Routing locally originated traffic after failover in 1.9.0
That is may be because you have valid routes in main table I can't fully agree with: >> No, it can't be rubbish, it has to be real. The load-balance engine looks up the main table for default...
View ArticleRe: Unable to go from 1.8.0 to 1.9.1 (and 1.9.0)
Generally the reboot helps if the router's been up for a long time, because it clears out logfiles, and any other tempfiles that may have accrued. Which router model are you using?
View ArticleLoad-Balance Failover with more than 2 interfaces
Hi ! How to make 4 WAN interfaces in Load-Balance Failover ? If you specify second failover interface it will say: root@ubnt# set load-balance group VPS interface eth2 failover-only Error: only 1...
View ArticleRe: Routing locally originated traffic after failover in 1.9.0
Another aproach to load-balance ))) https://help.ubnt.com/hc/en-us/articles/205202660-EdgeMAX-Automatic-WAN-failover-with-PBR-load-balancing
View ArticleRe: Unable to go from 1.8.0 to 1.9.1 (and 1.9.0)
I have a EdgeRouter Lite and the reboot trick didn't do it for me. I am running 1.9.0.
View ArticleRe: Config: Azure IPSec VPN with BGP (ERL 1.9.0)
I have this working on an ER-8, ER-Max(SPF). What are you running for settings? Do your SA's get setup?
View ArticleClik here to view.
How to Peer with a 2 Public AS and peer iBGP in these Routers?
I want to configure iBGP in these EdgeRouters:
View ArticleRe: EdgeMax No IPv6 Networking After Upgrade to EdgeOS V1.9.1
Correct, clients only have link local address i.e., those starting fe80.Have applied the command you suggested in your prior post, though since IPv6 is still "experimental" for our clients, rhe...
View ArticleRe: 1.9.0 broke dashboard for me (using Firefox)
Does anyone know how to get it to work on Safari, Chrome, Firefox, Mercury, etc on an iPad? Ever since I upgraded to iOS 10, routes and distribution stopped working on dashboard (mercury was the only...
View ArticleRe: 1.9.0 broke dashboard for me (using Firefox)
Ok just found out that 1.9.1 does not allow the devices in the discovery window to be sorted by IP address. this was fixed so e time ago per my request (it worked in 1.8.5) but now not working in...
View ArticleRe: Edgerouter X web pages not loading properly or delayed
That is good! It's why I need to make sure that I double-check my DNS. If only I could get some time for Christmas.
View ArticleWan address within the local network
The default firewall seems to block the an open port using the wan address when i am inside the local network.I have a dvr with the ports open and an app setup on my phone using the wan address to view...
View ArticleMulticast on a separate VLAN
ER-XFrom my ISP I get internet on VLAN 7 and the IPTV on VLAN 8.eth1 is WANeht0 is LANInternet comes to the LAN "set interfaces ethernet eth1 vif 7 pppoe 0 ...." without further configuration. The IPTV...
View ArticleRe: EdgeMAx on IPad
It works fine on my iPad on 1.9.1 in Safari (on a ER-X-SFP). The UI is slightly smushed but works fine enough. Are you by any chance using https with a self-signed cert on the edgerouter? I found...
View ArticleRe: Wan address within the local network
That doesn't look like a problem to me, but a misconfiguration instead.Make sure you have "hairpin NAT" enabled at firewall/NAT / port forwarding.Also make sure the that valid external IP address is...
View ArticleRe: Multicast on a separate VLAN
Yes eth2 is the simple solution.But it is possible to control the multimedia device with special apps (android).I will control the multimedia device over WLAN, for this both device must be in the same...
View ArticleClik here to view.
Re: EdgeMAx on IPad
Thanks for the reply. No I am not using any self-signed certs. It does appear that on the iPad using Chrome, it says NET:ERR_CERT_AUTHORITY_INVALID. On FireFox it says "This Connection is Untrusted"....
View ArticleRe: Unable to go from 1.8.0 to 1.9.1 (and 1.9.0)
Please use the CLI to upgrade, it'll give you exact error where the problem is. Copy/paste the error here. Exacute following command from CLI For ERLite-3 and ERPoe-5add system image...
View ArticleEdgerouter X crash, factory defaults afterwards
Bought an Edgerouter X, all setuped, but after a while (hour or so) it just crashed and rebooted with factory defaults. So I can't even see what happened... Any idea anyone? I have the idea it has to...
View Article