Re: Edgerouter pro DPI not showing as much detail after 1.9.0
Try 1.9.1 and update dpi signaturesCheers,jonatha
View ArticleRe: MPLS Guidance
Current config gives below results: show ldp session (R1)Peer IP Address IF Name My Role State KeepAlive10.10.2.2 eth3 Passive OPERATIONAL 30 show ldp...
View ArticleRe: Routing locally originated traffic after failover in 1.9.0
No, it can't be rubbish, it has to be real. The load-balance engine looks up the main table for default routes to establish default route for each defined load-balanced interface and it's respective...
View ArticleRe: EdgeRouter X Port Forwarding - Dysfunction
USG seems to be more consumer friendly... also i m not using all ports on the edge R X so i can remove it from the modem replace it through the usg for pppoe connections and use the edgerx later in the...
View ArticleRe: Still stumped 3CX behind NAT
ok, that makes sense i think...but it is still working 12 hours later.....so...any idea on how or why?
View ArticleRe: Edgerouter pro DPI not showing as much detail after 1.9.0
I dont see 1.9.1 available for download
View ArticleRe: Still stumped 3CX behind NAT
Also, I have SIP ALG disabled, doesnt this disable the conntrack table?
View ArticleRe: Edgerouter pro DPI not showing as much detail after 1.9.0
after digging around on google I found it. I'm going to install it in the morning and i will advise of my results
View ArticleClik here to view.
Can i assign a certain port to be a dedicated vpn port?
Hi All, I am looking into getting an EdgeRouterX and just wondered if it would support the following... I would have eth1 as my normal network 192.168.11.1 and it will go into a switch which all other...
View ArticleRe: IPv6 6rd setup
Hello, In my search for ipv6 I've been given the following page: https://help.ubnt.com/hc/en-us/articles/204960044-EdgeMAX-Enable-IPv6-support-via-CLI Maybe it will help you.
View ArticleRe: Multiple IP WAN : auto firewall, NAT and port forwarding
dpurgert: thanks, I understand nowcouple more questionsif I also need to forward a range, do I do a dnat and firewal for that also.I need to open 9000-9010 at least Also, what is keeping nefarious...
View ArticleClik here to view.
Re: Multiple IP WAN : auto firewall, NAT and port forwarding
Many thanks , Just another question, in the 's example, how to select only one WAN IP address in the ruleset configuration for WAN_IN ? Based on this example, I would like WAN IP x.x.x.1 port 8080 for...
View ArticleRe: Multiple IP WAN : auto firewall, NAT and port forwarding
make a dnat for each one 1. source of WAN1, Destination of port 8080, translation of lan ip 1 port 802. source of wan2, destination of port 8080, translation of lan2 port 80
View ArticleClik here to view.
Re: Multiple IP WAN : auto firewall, NAT and port forwarding
mprattmd wrote:make a dnat for each one 1. source of WAN1, Destination of port 8080, translation of lan ip 1 port 802. source of wan2, destination of port 8080, translation of lan2 port 80 Will you do...
View ArticleRe: Can i assign a certain port to be a dedicated vpn port?
I'm not exactly sure what the goal is for what you are trying to accomplish. You could have a network on eth2 that uses policy based routing to send traffic to a VPN (must be VTI, openvpn, etc. with a...
View ArticleRe: IPv6 with DHCP-PD on 1.6?
Sorry to dig up and old thread, just checking to see if has IPv6 working. I have literally the same setup and am running into a wall on this.
View ArticleClik here to view.
Re: Multiple IP WAN : auto firewall, NAT and port forwarding
Will you do that in the WAN_IN ruleset ? or in the DNAT rule configuration ? or both ? You will add the source address and port for the DNAT rule. You'll need WAN_IN rules for both of the LAN IPs and...
View ArticleRe: Multiple IP WAN : auto firewall, NAT and port forwarding
in my mprattmd example above, what would keep nefarious activity out of port 5060 from the world? should I add a source addresses of the voip provider, or is that neccessary?
View ArticleRe: 1.9.1 Firmware Update Check
UBNT-afomins wrote:greigm wrote:Is there any configuration for this, specifically to enable/disable?No, firmware update check can not be disabled. I would like to clarify that this is just a first step...
View Article