Re: IPSec tunnels with main site prefix overlapping remote site networks no...
Thanks for your feed back.Because 'ip rule 220' means any packets which are not marked as 0xffffffff, will lookup table 220. So the packet to local network will also lookup table 220. That is why we...
View ArticleRe: Strange behavior with load-balance
I would like to clarify few things:Apart from showing "gateway" instead of "route-table", was there any other issue? Was loadbalancing working as expected or not?Was it one time occurence or it is a...
View ArticleRe: Edgerouter X web pages not loading properly or delayed
Is this happening for ppptp users or for LAN users or both? Try disabling traffic-analysis. Any difference?
View ArticleRe: EdgeRouter Speed Issue
Also check that flow accounting isn't enabled. I had an issue with my connection capping out about 50mb/s below what i should be getting it i traced it back to flow accounting being enabled on my WAN...
View ArticleRe: BGP routes not advertised
Does BGP neighbor session establishes correctly? Show output of "show ip bgp summary"Enable BGP debugging - "debug bgp"Restart BGP sessionIn /var/log/messages you will see logs that should explain the...
View ArticleRe: IPSec tunnels with main site prefix overlapping remote site networks no...
Which strongswan patch are you talking about? Can you give us a link? Thanks!
View ArticleRe: Ubiquiti EdgeRouter and Plex
The port-forwarding looks right, although I note mine is using protocol tcp_udp (coincidentally also rule 5 on mine) rule 5 { description Plex forward-to { address 192.168.1.5 port 32400 }...
View ArticleRe: Another EdgeMax QoS Thread - Questions about packet prioritization
Don't use too much classes 3 or 4 will do fine. Just make sure bulky up/downloads take full bandwidth , filling up buffers is already very helpfull The classes as shown look OK.....but you do not set...
View ArticleRe: BGP issues V1.9
You can troubleshoot this issue:Enable BGP debugging - debug bgpRestart BGP session with 172.23.80.1;Check contents of /var/log/messages - you should see reason why incoming prefixes are not accepted
View ArticleRe: Help with QOS please
3) use ssh program like putty, this way you can copy/paste from notepad. What commands / queue types are you trying?
View ArticleRe: Firewall and DNAT question
DNAT happens BEFORE firewall. Firewall does not block DNAT. Associated firewall rule for DNAT must match on translated addr/port.
View ArticleRe: /etc/default/ssh is unwriteable!
Normally , a CLIcommands like below sets port as wanted:configure set service ssh port 2222 commit save exitHowever, you're using port 161, which might already be in use. Try to avoid messing with...
View ArticleRe: How to repeatedly crash an ERX
Ha! I started with such a complicated setup that I never thought to test it with a single ERX. So... back to the test bench. Interestingly, the problem does not occur with only one ERX. At least two...
View ArticleRe: /etc/default/ssh is unwriteable!
The file is normally writable by root, you may have corrupted file system. I've just tried. The config can write to it too. Can you write to anything else on /etc?brano@router:~$ ls -al...
View ArticleRe: EdgerouterPro2Switch via SFP module
On the switch is the physical mode for the SFP port you are using set to auto negiatiation or manual 1000Mbps full duplex? Could you try manual if on auto?
View ArticleRe: Help with QOS please
I'll give putty a try. I have tried this: https://community.ubnt.com/t5/EdgeMAX/Guest-QOS-or-Bandwidth-limit-per-vlan/td-p/1527542(mojo_333 / 2014-04-04, 2:36PM post) It strikes me as wrong that both...
View ArticleRe: Ubiquiti EdgeRouter and Plex
Hi - I want it to be accessible externally and internally - neither of which is working currently. I tried changing it to TCP/UDP and it still isn't working - do you have a dual WAN/LAN setup as well?
View ArticleRe: Ubiquiti EdgeRouter and Plex
In the webadmin, have you checked the box that enables remote access in Plex?As Alex said, TCP-UDP may help too, I have mine set to allow both protocols.By chance, are you using a domain to access your...
View ArticleRe: Ubiquiti EdgeRouter and Plex
I don't have a daul-wan setup at the moment, but I did have in the past, using an ER-5-POE, and it worked with Plex. Let me find an old config from that router. and post it here for you to look at.I...
View ArticleRe: Ubiquiti EdgeRouter and Plex
just looked again now - I need to add /web/index.html after the port 32400so it would be http://xx.xx.xx.xx:32400/web/index.html and it works - try that maybe?
View Article