Re: Edgerouter as IPSEC client VTI
Yeah i saw that but its rather sparse and deals with converting a config from site-site ....not enough information for me personally to go off of....
View ArticleClik here to view.
Re: OpenVPN client on edgerouter for management purpose
Ok i tried the route-nopull. But no success, after checking the ap's in the unifi controller they went down. However vpn was working... FYI: WAN is dhcp
View ArticleRe: Time to update the guts of the ERL?
An ERL with a PoE switch would be awesome, although the biggest thing I'd like is more raw power and still a fanless design. If QoS could be done in hardware that'd be fantastic too, but with all the...
View ArticleRe: ER-X - Corrupt downloads
We have the same problems. Can you post your final config file that works fine for LAN clients ? Your ISP is Orange? Regards
View ArticleRe: Norwegian Altibox - ER-X-SFP - can't seem to get internet connection thru...
As I work with Fibre on a daily basis, I just told my friends at the USA that I needed an sfp instead of a modem, witch they were fine with. I can however, check the brand and model for you later. But...
View ArticleERX slow access to WebIF through Firefox
Hello, I have difficulties to access to any ERX SFP with Firefox.With Safari the web page appears instantly...But with Firefox it takes 30 seconds to show the login page! And the page is not very...
View ArticleRe: One to One NAT
Taking another look at the settings on the watchguard box, it looks just as likely that it's just doing masquerade or randomly picking a public IP as it would be to actually be doing 1:1 NAT. And...
View ArticleRe: One to One NAT
Sorry I'm not sure what you mean. The WatchGuard rule uses the last octet of the public subnet and then forwards that particular packet to the last octet of the private subnet. I am just looking for a...
View ArticleRe: migrate from ER Lite to ERP
bourboncowboy wrote:Is it as simple as downloading the config from the ER Lite then uploading that same config to my new ERP? Will the upload wipe out everything from the ERP?Copying config between...
View ArticleRe: ERX slow access to WebIF through Firefox
I don't use Firefox often myself, but I haven't noticed issues connecting using. I assume you have updated Firefox too, what version and OS are you using.
View ArticlePersistent site-to-site VPN with automatic dual WAN fail-over
Hypothetical: I have a server setup behind an EdgeMAX router that has dual WAN fail-over configuredIt needs to maintain a persistent site-to-site VPN connection between two other EdgeMAX routers over...
View ArticleRe: Edgerouter as IPSEC client VTI
First you'll need to get the tunnel up between your EdgeRouter and your provider. Where are you getting stuck with this?
View ArticleRe: One to One NAT
As I said, I'm not familiar with the watchguard setup. The way I'm reading it, it looks like it's just as likely to NAT 10.x.x.10 -> 86.x.x.10 as it is to NAT 10.x.x.10 -> 86.x.x.200. Given that...
View ArticleRe: One to One NAT
On both dNAT and sNAT rule, you can use /24 mask on destination address / translated address.This way a single rule does translation for all 256 addresses.
View ArticleRe: Port Forward Help
The configuration looks okay. It is missing firewall rules in WAN_IN if using only manual DNAT, but auto firewall is enabled for the port foward wizard so that should be okay. You are on an older...
View ArticleRe: host name not resolving across subnets
I have this working using dnsmasq enabled for DHCP with static host name for a device.Using CLI: configure set service dhcp-server use-dnsmasq enable set service dns forwarding listen-on eth1 (use your...
View ArticleRe: One to One NAT
How would I go about doing this? Sorry for being a "newb", it's just new to me. I don't have a "catch all" masquerade rule either, what does this rule look like?
View ArticleRe: RDP not working inside network
Ugh, that was it. My old network was on the 192.168.1.x subnet and I moved it to 10.0.1.x. I guess Windows would just assume 192 was local and 10 wasn't. Thanks for the help.
View ArticleRe: ER-X packet loss
I just submitted a ticket so we will see what they say. My replacement router just doesn't handle multiple connection well.
View Article