Re: Time to update the guts of the ERL?
I completly agree. I'd love to see something with a switch chip (so we can bridge at line rate), a better CPU, more ports (not just Ethernet, a usable external USB port would be nice). Buried somewhere...
View ArticleRe: vlc or iperf causing packet loss
video_ wrote: During a continous ping between the two systems packets will drop - destination host unreachable and request timed out. Check the ARP tables. The destination unreachable is normally seen...
View ArticleI can not go to EdgeRouter Lite device.
Hello. Help is needed. I can not go to EdgeRouter Lite device. Did reset. I can not detect it. Help.
View ArticleRe: EdgeOS GUI not displaying properly in Firefox
Thanks guys! I'm glad I'm not the only one having this problem. UBNT PLEASE FIX THIS!!
View ArticleRe: Edgerouter OpenVPN
Did you run openvpn as administrator on windows?While connected to openvpn server, which is the output ofnetstat -rCheers,jonatha
View ArticleRe: ERPOE5 cannot reach eth0 subnet from switch0 subnet
There's nothing in your router's firewall that would block the eth0 network from switch0's, unless for some reason the firewall thinks that the NAS is "streaming media". That being said, if you're...
View ArticleRe: I can not go to EdgeRouter Lite device.
After factory reset you need to set your PC to a static IP 192.168.1.2 and then access the router at 192.168.1.1 on eth0. If that does not work get a console cable and see what's going on. The internal...
View ArticleRe: Disabled interfaces still work
czechu wrote:@UBNT-afominsplease check it, thank youWe are aware of this issue, but it has not been fixed yet.
View ArticleRe: LB ping interval
By default ping interval is 10 seconds: ubnt@skyler# set load-balance group zzz interface eth1 route-test interval Possible completions:<1-65535> Ping interval in seconds (default 10) [edit]
View ArticleClik here to view.
Re: ERPro-8 policy routing with three internet connections
Thank you very much! I didn´t know I could do that. rule 90 {action modifydescription "restrict SMTP to interfaces having a static IP"destination {port 25}modify {lb-group SMTP}protocol tcp} group...
View ArticleRe: large (ish) downloads failing on load balance setup
Try setting load-balancing sticky option that will cause established flow to use same egress interface per destination: set load-balance group LoadBalance sticky dest-addr
View ArticleRe: ERPOE5 cannot reach eth0 subnet from switch0 subnet
Thank you. I am puzzled too. Neither Mac nor Win can access it from 192.168.1.0 subnet...
View ArticleClik here to view.
One to One NAT
Hi,We're moving away from WatchGuard appliances to Edge Routers. We have a bunch of NAT rules which frankly I'm quite baffled with how to configure in 'EdgeOS' terms. How do I configure 1:1 Nat rules...
View ArticleRe: ERPOE5 cannot reach eth0 subnet from switch0 subnet
Okay, reset the firewall rule counters for that 'parental control' ruleset (should happen if you swap two of the rules around and save, IIRC). With nothing else connected, try accessing the NAS box...
View ArticleNo internet on Edgerouter PoE
Hi, I have problem to connect to internet with my new Ubiquiti Edgerouter PoE.. Firmware V1.9 is downloaded and installed on the router. And I have done the wizard setup on the WAN+2LAN2, that is...
View ArticleRe: One to One NAT
"Dynamic NAT" seems to simply be Masquerade (I think ... not familiar with that brand). 1:1 NAT is straightforward, you just need a DNAT rule and a corresponding SNAT rule. DNAT RULE rule 7 {...
View ArticleRe: No internet on Edgerouter PoE
Are you connected via a Cable ISP (e.g. Time Warner / Comcast / Cox / etc. in the US)? If so, is the ER replacing something else? Most likely, the ISP locked your account to the previous router Turn...
View ArticleRe: I can not go to EdgeRouter Lite device.
Network checked. The flash drive is working. All interfaces connected. In addition to the console. 192.168.1.1 does not ping. Console cable will be too late.
View ArticleRe: I can not go to EdgeRouter Lite device.
Try unplugging all the interfaces other than the one you use to connect to the device? I've had issues after firmware updates where the ERL and ERX both go completely unresponsive and stop working,...
View Article