Re: Dual PPPoE WAN same ISP
Two PPPoE from the same ISP is no problem, the restriction on shared gateway IPs is only applicable to Ethernet, not PPPoE. Guessing you probably don't have any config in place to load balance...
View ArticleRe: un-natted packets being sent out the WAN interface
What traffic specifically is it that's going out without NAT?
View ArticleDiagnose failing port forwarding?
I have an app on my iphone that access a hardware device on my LAN. Until recently, it was working without a hitch. I have a simple port forward rule from a fixed WAN port to a fixed LAN port. The...
View ArticleRe: Dual PPPoE WAN same ISP
I give you my configuration, if you can tell me why it does not balance ubnt@EDGEMAX:~$ show configurationfirewall {all-ping enablebroadcast-ping disablegroup {network-group PRIVATE_NETS {network...
View ArticleUbiquiti EdgeRouter POE loading problem
Good afternoon!Recently constantly problems with the new routers EdgeRouter POE, refused to load properly if they are Connecting switches Netgear, Provider Router and UniFi access points Poe (24 or...
View ArticleNot able to get site to site VPN up
Hi, I am trying to a get a site to site VPN link up and I get this error message :Me@EdgeRouterPro8:~$ sudo swanctl --log 12[IKE] sending retransmit 3 of request message ID 0, seq 1 12[NET] sending...
View ArticleRe: OPENVPN ports changing which blocks access.
I just had a very similar situation (suddenly down after months working, rejected because wrong port). I still did not figured out what happened, I just changed the ports in the configuration to...
View ArticleAnother OSPF/ECMP question :--)
O E1 *> 0.0.0.0/0 [110/20] via 10.3.1.1, eth0.31, 00:09:02O *> 10.0.0.0/16 [110/11] via 10.3.1.1, eth0.31, 00:26:03 *> [110/11] via 10.2.6.1, eth1, 00:26:03C *> 10.1.1.0/24 is directly...
View ArticleRe: Diagnose failing port forwarding?
Does it work on LAN or WAN or broke on both?What port (LAN or WAN) are you doing the tcpdump? It sounds like they are getting into the router (rule stat counter) so do a tcpdump on the LAN port and see...
View ArticleClik here to view.
Re: Can't see lan clients
Hey! and thanks for helping! So to make things easier I here is a quick picof how things dont work: And this is how it does work:As for the show config command, that is everything it output.As for...
View ArticleRe: Another OSPF/ECMP question :--)
Seems to me like the E1 default route doesn't "win."It gets beaten on both longest subnet match (=1st check) and worse route distance (=tie-breaker) Since both use same next-hop , you can't tell the...
View ArticleRe: Packet Capture and Website logging
1) Netflow would well on the router.2) You could use PF as a passthough firewall before the gateways and run ntopng for a complete traffic view across the br0 port. Thanks,David.
View ArticleRe: Can't see lan clients
Just re ran the config command, and figured out how to display more. So full display now above.
View ArticleHairpin NAT not working since 1.6.0 to 1.9.0 upgrade
Hi all, I've just upgraded my ERPoE5 from 1.6.0 to 1.9.0 and have noticed that the Hairpin NAT function has stopped working. I have a number of services running locally on my network which are shared...
View ArticleRe: Not able to get site to site VPN up
I'm having exactly the same issue with a site-to-site link between an ERPoE5 and an ERLite3. IPSec site-to-site was working perfectly under 1.6.0, but refuses to connect under 1.9.0.
View ArticleRe: Can't see lan clients
do "show configuration | no-more" and paste that output. as syas, the commands are okay, but the actual config is more telling.
View ArticleRe: overwhelmed to say the least
Deleted Account wrote:I understand how to troubleshoot. I get paid to do so. There's not much to mess up with smart queue and basic queue. That's where everything goes south. As stated before,...
View Article
