Re: Peculiar firewall configuruation brought to you by TiVo
the uap is just a l2 bridge. it shouldn't do that. COuld be the asus router having a coniption because you're using the UAP (SOHO routers tend to not play well with external devices such as APs ......
View ArticleRe: IPSec VPN not working 1.9.0 - any tips for debugging?
HiThanks for a very detailed thread. I have spent nearly two weeks trying to resolve this issue, reviewed every L2TP post I could find and watched every video. I tore apart my firewall muliiple...
View ArticleRe: EdgeRouter X v1.9 VLAN enabled switch blocking VLAN traffic
Coming from cisco routers/switches, I'm accustomed to both config styles:1) On L3 switches , VLAN1 (vif1) is used for untagged packets.2) On ISR router ports, untagged IP can be put right under the...
View ArticleRe: EdgeMax and netflow: all my packets are registered twice...
Can you do flow accounting on either eth0 or eth1 ?br0 might see packet twice: first receive on eth0 , then send on eth1
View ArticleRe: RFC1918 Filtering
The ER doesn't do that onitself. I dislike firewall_out rules, alternatively , you can black-hole route these entire subnets.
View ArticleRe: L2TP VPN Clients can't access LAN
You might find this post useful: http://community.ubnt.com/t5/EdgeMAX/Setting-up-L2TP-VPN-server-no-access-to-network-resources/m-p/1678435#M128418
View ArticleRe: internet speed issues
anyone else have any ideas why i'm not getting the full 100 meg. When I do speed test's my speeds are all over the place no matter if it is wired or wireless. do I have a defunked unit? Thanks,
View ArticleRe: EdgeMax and netflow: all my packets are registered twice...
nope, that is not working. If I try configure that, no packets are sended out...
View ArticleRe: internet speed issues
As say please post your full config. We can't guess at why you haven't got it quite right.
View Articleedge pro vs watchgaurd xtm 330
I am trying to decide which firewall/router to go with. A 5year old watchguard xtm 330 or a edgerouter pro. The specs for each are a 'bit' confusing. The comparison is as...
View ArticleRe: dual-WAN policy routing won't load balance
Recommended changes: - Remove dhcp--option from eth0 since it's not using dhcp- Remove "modify balance" from pppoe0 and eth1. The modify is for LAN traffic not WAN.- "set interfaces ethernet eth1...
View ArticleRe: Edgerouter X ipv6 hwnat
Did this get resolved for the OP? I just setup a new ER-X-SFP on 1.9.0 using the GUI/wizard and everything was working fine when it came to IPv6. However, after enabling hwnat offload, IPv6 isn't...
View ArticleRe: Can't connect my new EdgeRouter PoE to Internet
beischer wrote: I have configured the router with the wizard using "WAN+2LAN2" with DHCP, no firewall (tried with firewall also), Bridge LAN interface into a single network). What to check next?...
View ArticleRe: Time based firewall rules & force DNS to specific subnet
Hi..I found the problem is my network always go to 2nd WAN (failover only).When I do traceroute to 8.8.8.8 from EdgeRouter it go to 1st WAN (pppoe).But when I trace route from my network (from my...
View ArticleRe: Edgerouter X ipv6 hwnat
Was never able to resolve the issue. Was told it must be an issue with my isp because it functions on other isps and the result of the packet capture I sent in. I'm not sure where the bug actually is,...
View ArticleRe: Can't connect my new EdgeRouter PoE to Internet
Maybe post the config. Make sure you are getting an ip on the Internet interface and that you have a MASQ rule setup under NAT
View ArticleRe: Edgerouter X ipv6 hwnat
blizzard242 wrote:Was never able to resolve the issue. Was told it must be an issue with my isp because it functions on other isps and the result of the packet capture I sent in. I'm not sure where the...
View Article