Re: statuscake auto address-group population?
Finally did this, and turned out to be way easier than I thought... #!/bin/bash WHITELIST=$(curl -s https://www.statuscake.com/API/Locations/txt) sudo ipset flush statuscake for IP in $WHITELIST do...
View ArticleIssues with My Setup
Right now my setup is as follows: Cable ModemWatchGuard T10 (Soon will have a M200)2 EdgeSwitchsActive Directory ServerWith this setup I'm having a lot of issues with my older Apple TVs exhausting my...
View ArticleRe: will it work?
An ER-X should be sufficient at both towers, I have the X's running on multiple sites, some of which are handling traffic from 50 or more clients with no issues as well as traffic from sites behind...
View ArticleRe: Cake compiled for the ERL
Looking at this post for second time in more depth... Comparing the first sch_cake and fq_codel charts, shows better averages on the tcp download and latency charts using sch_cake... I had to look up...
View ArticleRe: Cake compiled for the ERL
: This page on the Bufferbloat.net wiki summarises this better than I could: Cake. There's also more technical information available here: Cake Technical. : No is right, when comparing sch_cake (w/...
View ArticleRe: Cake compiled for the ERL
Given how low the upload bandwidth is, I'd try SFQ here, without offloads, for comparison. stig - a portion of cake's design was heavily influenced by our edgerouter experience - cake explicitly peels...
View ArticleMultiple source IP's allowed for the NAT port forward?
I can put in one IP address or a range. How about two completely different IP addresses that aren't in the same range? Can that be done from the GUI?
View ArticleRe: Cake compiled for the ERL
Am I understanding correctly that Cake is an evolutionary "upgrade" to fq_codel (a la UBNT "Smart Queue") AND avoids the heavy performance penalty inherent with disabling HW acceleration? Be still my...
View ArticleRe: ipv6 internal traffic gets filtered
I've decided to reset the ERL to factory default and start from scratch .... I suspect some form of corruption has set in that causing this very weird behaviour.
View ArticleRe: Configuring 4WAN 1LAN Load Balancing
yes... now i plug only 1 WAN on eth0.. its working. and able access to the internet... will plug in other WAN at different site tomorrow. so, basically this switch0 will supply the load balance...
View ArticleRe: Cake compiled for the ERL
netrunner wrote:Am I understanding correctly that Cake is an evolutionary "upgrade" to fq_codel (a la UBNT "Smart Queue") AND avoids the heavy performance penalty inherent with disabling HW...
View ArticleRe: Multiple source IP's allowed for the NAT port forward?
Firewall/NAT => Firewall/NAT Groups => + Add Group
View ArticleRe: Cake compiled for the ERL
stig: the portion that I'd hoped be handled properly was GRO peeling on the interface with cake on it. are you saying that enabling qos on one interface disables all offloads on the others?
View ArticleRe: Cake compiled for the ERL
netrunner wrote:Am I understanding correctly that Cake is an evolutionary "upgrade" to fq_codel (a la UBNT "Smart Queue") AND avoids the heavy performance penalty inherent with disabling HW...
View ArticleRe: Cake compiled for the ERL
@Lochnair : thank you very much for doing the backport and the testing! four items of note: 1) rrul is a really nasty test (intentionally so!) and shows how badly uploads do no matter what we try, when...
View ArticleRe: IPTV setup help
I realise I sound like a wolly but I do understand the difference between a modem and a router! My modem (draytek vigor 130) actually had a new firmware with 1520 MTU and such which lets it provide a...
View ArticleWAN + 2LAN
Hi, my setup is as follow: eth0: WAN from ISP eth1: 192.168.1.0/24 GW: 192.168.1.1/24 eth2: 10.10.10.0/24 GW: 10.10.10.1/24 Both eth1 and eth2 can access the internet. However, I am having problems...
View ArticleRe: IPTV setup help
Doh! Think it was my modem all along; when I hooked up the modem to my PC i noticed it had a *LAN* ip of 192.168.2.1 it also seemed to have its own igmp proxy. I set the modem to 192.168.99.1/24 so it...
View ArticleRe: IPTV setup help
Glad it's working, I'd assumed that you were just using the openreach modem.
View ArticleIPSec VPN not working 1.9.0 - any tips for debugging?
Hi, I have followed UBNT-Jamie tutorial for creating the IPSec VPN from by ER-X running 1.9.0 but I can't seem to connect from any of my devices. Any pointers in problems with my config / advise on how...
View Article