Re: 1.9.0 broke dashboard for me (using Firefox)
Well spotted... I've just tried going back to Safari, telling it to trust the certificate and it now works. I suspect the main issue was down to the lowercase letters and we just needed to then trust...
View ArticleClik here to view.
Re: 1.9.0 broke dashboard for me (using Firefox)
PS It is so nice to have the webstats back!
View ArticleRe: Business Park Build your own WISP - Help Needed.
In general I think what you have would work - however, you don't really need or want to have the static IP's on all individual radios. The below is simply one way of doing it- not saying it's the best...
View ArticleRe: auth.log shows iptables being manipulated
Some of those commands look like what happens when you do "show load-balance status".
View ArticlePort forwarding is not working at all, port remains closed.
I'm new. Not much of a network dude, so please bare with me. I've recently bridged my áll-in-one' modem to my router...so now the modem is running solely as a modem. Everything else is disabled and...
View ArticleRe: 1:1 NAT Issue
Where are you trying to ping X.X.X.228 from? If you're attempting to ping X.X.X.228 from any interface except br0, the NAT translation won't work since you have the inbound-interface set to br0. You...
View ArticleRe: Sharing a Printer Among All Interfaces
Thank you. You are right, other than the default firewall rulesets on WAN (eth0), there are no other rules when Basic Setup wizard is configured. What I ended up doing was, to set an IP manually for...
View ArticleRe: Port forwarding is not working at all, port remains closed.
First, in WAN_IN, move rule 30 before rule 20. Leave the invalid state rule second only behind established/related. In your current rule 20, add address 192.168.1.107 to destination. In nat rule 1,...
View ArticleRe: Firewall - block/open options
I'm not specifically looking for a solution to my issue - I know it has something to do with a specific type of traffic I need to block. I'm curious what other people are doing - just trying to get...
View ArticleRe: 1:1 NAT Issue
I can ping the IP from outside, meaning from another computer on a different ISP. I just tried your suggestion with the same results. I cannot access SSH or HTTPS with the .228 IP. I did get a warning...
View ArticleClik here to view.
Re: Edgerouter Pro high CPU with traffic shaping policy for 500mbit
Your results are along expectations, since QoS disables offloading traffic.
View ArticleRe: Firewall - block/open options
You didn't say if the rules you've mentioned are on WAN_in or WAN_out or WAN_local? Typical setup in our business is WAN_in default DROP and allow only established and related. Punch holes for specific...
View ArticleRe: Hairpin nat with multiple subnets / vlans
1st of all , don't expose tcp 445, this is for windows filesharing and not required for exchange access. Preferred way is to configure dns-forwarder to return internal IP for exchange when using its...
View ArticleRe: Help with GRE tunnel between two edgerouter Lites
The GRE tunnel itself should pass multicast, allowing OSPF to run on it.But that only handles multicast ...on a single interface.You also have to enable multicast routing between interfaces by...
View ArticleOutside Webproxy
I see many articles on how to enable webproxy for the local lan but none of them explain how to enable it for the wan interface. How could I do that?
View ArticleRe: Remote User VPN can't access site-to-site VPNs
is right that the L2TP ip address range used might break connectivity. However, simply adding routes might not work: On classic ipsec vpn, source and destination networks are manually configured....
View ArticleRe: CLI Integrated dnsmasq Adblocking & Blacklisting v3.5.5 Easy Config
Everything ran a lot smoother in 3.6; no more soft error and I was able to run through the full installation without issue. Thanks, good patch!
View ArticleRe: Firewall - block/open options
So it sounds like you fall on the side of lock down everything and allow specific ports in as needed. WAN_IN This was our orignal (and now current) setup - where we lock down the firewall and only...
View Article
