Re: Edgerouter Lite - Getting rid of Bell Canada's Homehub2000 ( Internet AND...
Here is the configuration. (Removed the username password stuff, but all in all, pretty basic) firewall {all-ping enablebroadcast-ping disableipv6-receive-redirects disableipv6-src-route...
View Articlestrange behavior DHCP traffic allowed during reboot
I have a EdgeRouter X SFPv1.6.7I have eth1 internet - provider router with DHCP or bridge mode - cable modem The "or" above does not influence...
View ArticleRe: EdgeRouter dashboard doesn't work with Safari
Same issue for me too! I work around it using Chrome for OSX, but would like to be able to use Safari.
View ArticleRe: EdgeRouter dashboard doesn't work with Safari
Neither of you stated which EdgeRouter you have. The image looks like an ERX given the interfaces shown. I have an ERL running 1.9.0 and I usually use Chrome which works fine. So I just tried the GUI...
View ArticleTunnel a Device to another Site in same L2 Subnet
Hello,I am looking for some basic hints/advices for a special configuration. I apologize for my English :-( Site AVDSL Connection with AVm Fritz!Box as Modem/Router. After this a ER-PoE. On ER-PoE a...
View ArticleRe: v1.9.0 IPv6, DHCPv6 PD and PPPoE problem
Hey - don't feel bad. Some things are learned the hard way. At least this issue got you talking on the board. Keep us posted on your IPv6 experiences.
View ArticleRe: EdgeRouter dashboard doesn't work with Safari
karog wrote:Neither of you stated which EdgeRouter you have. The image looks like an ERX given the interfaces shown. I have an ERL running 1.9.0 and I usually use Chrome which works fine. So I just...
View ArticleRe: Requests/suggestions for new hardware models
That's good to know, thanks. It sure would be nice to see upgraded versions of the 1G SKUs as well. I suppose the move to new SoCs might result in some initial instability, especially with features...
View ArticleRe: EdgeRouter dashboard doesn't work with Safari
I saw others mention that they had issues in Firefox as well so it's not limited to Safari.
View ArticleRe: strange behavior DHCP traffic allowed during reboot
Upgrade the bootloader to resolve this issueYou can also check bootloader version
View ArticleRe: 2 WAN Load balance failover not working
There is a little information describing your problem but maybe this help: "Note: If your WAN interface is PPPoE, it's a good idea to not get a route from the pppoe server and instead add an interface...
View ArticleIGMP forwarding accross bridge interface sourced from vlan interface
Hey guys I'm having some issue's getting multicast packets across the following setup eth0.15 < br1 > eth1.15 I'm sending multicast packets from eth1.15, they are seen on eth1.15 and br1 but not...
View ArticleERL OpenVPN Selective Routing not working
Hi all, I've been trying to get all my TVs to use an OpenVPN Tunnel. I've followed other people's guides that I've found on the internet such as this one and the posts marked "solved" in these forums...
View ArticleRe: WAN Load-Balancing OpenVPN server routing issue
I switched the config back to PBR, and while it seems it's routing OK now, with openvpn working properly, I have hit another bump: whenever I load the network (from a computer connected via ER LAN...
View ArticleRe: WAN Load-Balancing OpenVPN server routing issue
Another issue with both configs: if I use static interface routes, that ubnt tool gets called very often, ubnt-find-gateway.pl, which is also using quite a big chunk of processor. Combine that with...
View ArticleRe: After update to 1.9 not able to sent email whit macbook's
firewall { all-ping enable broadcast-ping disable ipv6-receive-redirects disable ipv6-src-route disable ip-src-route disable log-martians enable name WAN_IN { default-action drop description "WAN to...
View ArticleConfiguring additional OpenSSH server options within EdgeMax config
Hi, Is it possible to set additional OpenSSH options within the EdgeMax configuration itself? I.e. is there any SSH functionality similar to the 'options' command you can supply within your DNS...
View ArticleRe: ERL OpenVPN Selective Routing not working
If the ip address is TBD then it does not sound like it is fully connected. And if it is not fully connected then you certainly cannot expect traffic to go over it. Looking at your config, shouldn't...
View ArticleRe: Dual WAN Failover with OpenVPN Client
Anyone have any ideas on how to get this working? Just want to be able to tunnel traffic through VPN while keeping the dual WAN failover in place. Thanks.
View Article
