Re: EdgeMAX EdgeRouter security release frmware v1.9.1.1 has been released!
alex_cambui wrote:manu8383 wrote:My ER-X is bricked just after the upgrade to the last firmware. I deleted the backup image as suggested on your site. I have already tried to reset the device while...
View ArticleRe: VPN Internal Route Not Working (Determining Packet Destination)
I'll attach the config as a file. I don't know what lb-local is, but I'll check and see.
View ArticleRe: No internet when connected to L2TP VPN
Works after changing my internal ip addresses to RFC1918
View ArticleRe: Kernel version
dpurgert wrote:jms33 wrote:I do agree with @waterside, but as I said it's a divisive topic. It's in the best interest of UBNT, a publicly traded U.S. company, to keep their products secure. Sure,...
View ArticleRe: VPN Internal Route Not Working (Determining Packet Destination)
Under port-forward, try disabling hairpin-nat.It might masquerade packets both entering and leaving eth2
View ArticleRe: Edgerouter Lite single thread upload slow with hardware offload enabled
I got a notification to add my config, the config is listed below:firewall {all-ping enablebroadcast-ping disableipv6-receive-redirects disableipv6-src-route disableip-src-route disablelog-martians...
View ArticleRe: ER-X download speed optimizing
I have to askDoes hw-nat work with smartqos, or any qos for that matter?
View ArticleRe: UDP packet loss with EdgeRouter Lite
It appears my reply was deleted. Oh well, no matter. I'm losing about 0.67% on a 10Mb upload speed. It doesn't seem that bad.
View ArticleRe: Letsencrypt SSL support for Edgerouter
This should theoretically be possible if you have a working domain name pointing at your IP address, but implementation details are implementation details
View ArticleVPN (static) route issue
I think I'm having an issue with VPN connections seeing static routes. I have an IPSEC (IKEv1) VPN peer with 3 tunnels. 192.168.9.0/24, 192.168.11.0/24 and 192.168.12.0/24 The 9.0/24 subnet is directly...
View ArticleRe: Need help getting FIOS internet connection to work w/ Edgemax
I'm trying to remove the FiOS router from in the middle of things (connect the FiOS ONT directly to my EdgeMax Lite running 1.9.1.1). They were using cat5 to connect to my vz router, so I'm sure that's...
View ArticleRe: Another ERX FIOS setup question
See this DSLReports FAQ for where to find the WAN DHCP Release in the router GUI. It is several levels deep. From the same Verizon FIOS FAQ, this Lan to Lan option is what I have been using. It doesn't...
View ArticleRe: Another ERX FIOS setup question
Cool I'll check it out when I have a sec. Ubiquti community never disappoints!
View ArticleRe: VPN (static) route issue
Are these plain IPsec tunnes, or IPSec+VTI? On plain IPsec tunnels routing doesn't really apply, it's just the connected subnets. You need to convert to VTI based tunnels in order to be able to route...
View ArticleRe: VPN (static) route issue
They are NOT vti tunnels. Can you point me to a howto doc for those? And will it break existing non-VTI tunnels during setup?
View ArticleRe: Need help getting FIOS internet connection to work w/ Edgemax
I didn't spoof the VZ router's address. What if you unpleg the ethernet cable from the ONT to the ERL and leave it unplugged for 2 hours?
View ArticleRe: VPN (static) route issue
What if I don't have access to router #2, or it's not a Ubiquiti product? Everthing was working fine until I replaced the Endian firewall with this EdgeRouter
View ArticleRe: VPN (static) route issue
it was probably working fine with the Endian router because they use ipsec0 as an interface instead of whatever ubiquiti uses. I obvioulsy can't force all my peers to convert. If I can't get this...
View ArticleRe: VPN (static) route issue
ipsec0 sounds like virtual interface. If that's on the other side you may still get this working with VTI on your side. Try and see.
View ArticleRe: Need help getting FIOS internet connection to work w/ Edgemax
I can try that. Won't be working for at least 2 hours then Do I need to actually unplug it from the ERL? Does that make a difference? Thanks for the reply.-AJ
View Article
More Pages to Explore .....