Re: New ERX/AC-AP_LR setup guide for beginners.
Mike, kudoes for tackling this large project on yourown! I've only scanned briefly through your PDF, butit seems clear you not only did the work, but havediscovered several anomalies and oddities in...
View ArticleRe: Er-X crashing (I think)
Nope I submitted info captured in Syslog to support and they claimed it was faulty and needed replacing.Still not convienced, but replaced both the ER-X's with a single Mikrotik RB750Gr3. At some point...
View ArticleRe: Powering ER-X and AF-5X with AF-5X PoE
LLigetfa wrote:@jjonsson, Don't expect him to reply. Maybe a Netonix MINI would be a good fit there.I have an WS-6-MINI in the setup. But I need to provide VPLS service to customer, and that port must...
View ArticleRe: Newbie Edgerouter Lite internet connection problem
I determined my first problem in that I failed to enter anything into the system tab. I entered the address of my Uverse modem (192.168.1.254) and now I'm greeted with "can't resolve host" when I try...
View ArticleRemote access to find connected clients
Hi My old router (BT) allowed me to call a web page without logging on (within the network) to see connected clients. I used this in Node-Red to determine who was in the house by checking for the MAC...
View ArticleRe: Er-X crashing (I think)
Thanks for responding so quickly. I was just looking at what source code is available and the problem seems clear. The MediaTek offload driver is limited to a maximum of 16 concurrent flows....
View ArticleRe: Remote access to find connected clients
Do you need to know wired clients? If you only need to know wireless clients then UniFi portal will show you all those. As for wired you can check from router based on MAC or activity showing in DPI.
View ArticleRe: DHCP Negative Poolsize
I can get in CLI consistently now. Is there a way to disable this DHCP Pool and Enable a different one. I am unable to do it through the GUI
View ArticleRe: Powering ER-X and AF-5X with AF-5X PoE
How long is the run to the AF-5X? I would probably replace the ER-X with an ER-X-SFP and power the AF-5X from that.
View ArticleRe: EdgeMax Shows 4 Admin sessions
I'm not aware there is a way to do this from the BUI, but you can find the sessions via something like this at a shell: edgerouter$ netstat -an | awk '($4 ~ /:22|:80|:443/) && $NF ~ /ESTAB/...
View ArticleRe: DHCP Negative Poolsize
show configuration commands | grep dhcp-serverwill show all current dhcp server settings. Save into txt editor so you can re-use those commands at will Use command below to get rid of dhcp...
View ArticleEdgeMAX-X site-to-site vpn
two sitesZyxel USG50 to/from Edgemax 1.9.1Can contact devices/resources behind USG50 from devices/resources behind EdgeMAX.Cannot contact devices/resources behind EdgeMAX from devices/resources behind...
View ArticleRe: EdgeMax Shows 4 Admin sessions
I will log in tonight when I get home and see what it says again. Have it running my IPTV data stream to the Set Top Box and waiting for it to die as others have seen the ver 1.9.1 firmware lock up the...
View ArticleRe: Powering ER-X and AF-5X with AF-5X PoE
Have just tested. AF-5X PoE does not fry EdgeRouter X and does also power AF-5X... I'll let it run for some days to see if it gets toasted.....
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X ----Kernel Module hw_nat...
OK I think I fixed my problem. It works with v 1.9.1 firmware. I don't know why some people have problems and some don't except maybe there isslightly different hardware on some of the er-x models that...
View ArticleRe: Powering ER-X and AF-5X with AF-5X PoE
MimCom wrote:How long is the run to the AF-5X? I would probably replace the ER-X with an ER-X-SFP and power the AF-5X from that. I have no power at mast. Power must be provided from PoE to tower....
View ArticleRe: Powering ER-X and AF-5X with AF-5X PoE
My guess is that only half the pairs are energized on the output so cable length can be a factor.
View ArticleRe: Powering ER-X and AF-5X with AF-5X PoE
After looking at https://dl.ubnt.com/datasheets/edgemax/EdgeRouter_X_DS.pdf I can't see this should be a problem.... It seems that the EdgeRouter X is providing PoE out on 4 pins:Passive 24V (Pins 4,...
View ArticleRe: Powering ER-X and AF-5X with AF-5X PoE
The EP-R6 will take 4 pair power in so the 2 pair power out would be only for the short cable, not the full 30 meters.
View ArticleRe: Powering ER-X and AF-5X with AF-5X PoE
jjonsson wrote:and it takes up to 24VDC, 2.5A, so that AF-5X PoE 24V 1.0A shouldn't be a problem....Not through the PoE. PoE current is limited by the center-tap ethernet transformers and since only...
View Article
More Pages to Explore .....