Re: Edge Router and DPI / Unifi 5 Are we missing out?
Agreed. UNMS v2 will have Unifi integration.
View ArticleRe: Having trouble getting IPv6/DHCPv6-PD working on Comcast on v1.6.0
I sure did. I spent about 20 hours trying to figure out why my clients weren't getting an iPv6 address and was driving myself insane trying to figure out why it wasn't working...until I figured it...
View ArticleRe: Accessing certain admin tabs and SSH on an ER-Lite-3 hangs
Can you post your config?
View ArticleRe: Having trouble getting IPv6/DHCPv6-PD working on Comcast on v1.6.0
Thank you . I'm currently a world away and no longer using Comcast, but never did get this working previously after banging my head against it for hours. When I get back to the US in a few months I...
View ArticleRe: Having trouble getting IPv6/DHCPv6-PD working on Comcast on v1.6.0
Thanks , I had it turned on to help with Airplay. Its off now.
View ArticleRe: 3 WANS with PBR port fowarding issue
Didn't think of Split DNS. Any suggestions on implementing it?
View ArticleERPOE5 bonding 2017
Is there a timeline for when the ERPOE5 bonding capability will be able to work at the hardware level instead of using software to do it? I would really like to take advantage of this with an...
View ArticleRe: Updated Google Fiber + EdgeRouter Lite / PoE IPv4 & IPv6 config.boot and...
Steve, unfortunately your latest config.boot for PoE is not working for me at all. Eth0.2 never receives an IPv4 or IPv6 address.Do you think you could look into it?
View ArticleIKE - Fail to establish CHILD_SA
I have a ERPro with two IPSEC tunnels to ERX's. Both use rsa-keys and the configurations are identical on both sides. ERX #1 is up and running correctly, the second seems to be having an authentication...
View ArticleMy QoS does not work properly
I have 2 subnet for different outbound interfaces:172.16.8.0/23 -> pppoe1 (Telecom) -> eth1172.16.10.0/23 -> pppoe2 (Unicom) -> eth2 I want apply HFQ for all 172.16.8.0/23 clients to limit...
View ArticleRe: PLEASE HELP - EDGEROUTER Pro - dual Wan - dual NAT
For incoming connections, like sip registrations (all 5060 traffic) this should work. For VOIP conversations, it might not work, as some of the connections are initiated from the PBX (or at least...
View ArticleRe: Sticky Connection when doing PBR
See https://help.ubnt.com/hc/en-us/articles/205202690-EdgeRouter-Policy-based-routing-with-WAN-load-balancing for example using mark/restore-mark combo
View ArticleRe: ISP WAN Block IPs and LAN IPs Setup in EdgeRouter
Adding below onto your masquerade rule might do the trick: (make 5010 match your masq rule)set service nat rule 5010 source address !xxx.xxx.xxx.16/28This excludes xxx.xxx.xxx.16/28 addresses from...
View ArticleRe: (Solved) L2TP Stopped working after working fine for over a year.
I tend to skip most descriptions (seeing tcp80, I know without description it's web traffic) and never ran into this.If you do, foucus on output of "sudo iptables -L -n -v" to see if your configured...
View ArticleRe: GRE/IPSEC tunnel won't fully initiate until traffic is seen from the...
I'm beginning to think that from the OS perspective, once the packet is decrypted, a routing decision hasnt been made. The OS then needs to route it, but it's still on the outside interface andsubject...
View ArticleRe: Having trouble getting IPv6/DHCPv6-PD working on Comcast on v1.6.0
Let's not consider disabling IGMP snooping as a solution and something that always needs doing in the presence of IPv6. It should be used as a test and a short term workaround at best. Remember there...
View ArticleRe: IPv6 DHCP-PD, Clients not getting IPv6 Addresses
Let's not consider disabling IGMP snooping as a solution and something that always needs doing in the presence of IPv6. It should be used as a test and a short term workaround at best. Remember there...
View ArticleRe: IPv6 DHCP-PD, Clients not getting IPv6 Addresses
Well, it's an all ubnt setup. Edgerouterx, CloudKey, a mix of unifi switch 8's and 16's and ac ap pros. When snooping is on, IPv6 dies.
View ArticleRe: IPv6 DHCP-PD, Clients not getting IPv6 Addresses
Seems like similar has been seen on EdgeSwitch before. See BIG PROBLEM !!! IPv6 with IGMP Snooping Does Not Work and MLD Querier for EdgeSwitch. In the second post UBNT report they can reproduce the...
View Article
More Pages to Explore .....