Dual peth WAN - Dual LAN NAT hairpinning
Hello, I've 2 ISP assigned IPs on 2 pseudo-ethernet interfaces due to cabling limitations. First one (peth1) is for hosting and other (peth2) is for everyday use. Behind the NAT I have 2 LAN that are...
View ArticleRe: Updated Google Fiber + EdgeRouter Lite / PoE IPv4 & IPv6 config.boot and...
The difference may be that you are using a switch. I don't know how that works in a PoE ( I'm using a Lite). Does the switch support IGMP for multicast?
View ArticleRe: IMPOSSIBLE TO OBTAIN IP ADDRESS on VLAN
Will do as soon as I can get back to the site. If anyone has an idea on why it's not working please post so I can try when I'm back onsite.
View ArticleClik here to view.
Re: Updated Google Fiber + EdgeRouter Lite / PoE IPv4 & IPv6 config.boot and...
FYI - you are correct that the hwnat is enabled differently on the POE and ERL. It shows "hwnat disabled" but the "offload" sections are what actually enable it. I had noticed that in the configs and...
View ArticleClik here to view.
Google Fiber Network + DVR Combined box?
Has anyone been sucessful in getting an EdgeRouter in to act as the router when using GoogleFiber Gen2 Network box? They combined the Network Box (router) and DVR box into a single unit. I'd love to be...
View ArticleCan't block inter-VLAN routing
I have a few VLANs in play and two are guest networks so I am trying to keep them from being able to access all other VLAN's. For testing, I have VLAN 10 30 and 40 set up. All should be able to talk to...
View ArticleRe: EdgeRouter X - only getting 50 - 75% throughput
Definitely weird.I experienced a 15-20% increase in speed when I changed to my Ubiquiti equipment at home vs an all-in-one. Is your speed decrease there if you hardwire a laptop into the router, or is...
View ArticleRe: Can't block inter-VLAN routing
this may sound backwards, but try making it so that instead of the guest network blocking the corporate net, the corporate net blocks guest. the first thing i would try is put that firewall rule on the...
View ArticleRe: EdgeRouter X - only getting 50 - 75% throughput
All testing was done with 1 Gbps wired connections. It is making no sense to me.
View ArticleBlock Router IP Second Subnet
HeySo we are doing a bit of testing for a new deployment and have everything working some what fine, However we want to be able to block one subnet from being able to communicate to the other subnet....
View ArticleDestination Nat with Dynamic Source via ddns url?
Just wondering if it is possible to limit outside access to a nat rule with a url rather than using a standard IP. I have tried using and address group and failed. I have done this before on a...
View ArticleConfiguring IPSec VPN - connecting to lan clients
I'm trying to set up a home VPN. I want to be able to connect to the VPN to route all my traffic through it and connect to local LAN clients. I'm able to connect to the VPN, I just don't have any...
View ArticleEdgeRouter Lite S2S VPN - no routing
Hi everyone I managed to get a site-to-site VPN connection between my ERL and a Fritzbox using IPSec. The tunnel is up and running:$ show vpn ipsec sa peer-xxx-tunnel-1: #32, ESTABLISHED, IKEv1,...
View ArticleRe: New U-Boot image for better USB drive compatibility?
Thanks for this thread everyone! My ERL Lites have started dying and replacing the dead USB sticks with I have the same settling problem. I added a delay and reset as above and working well. One thing...
View ArticleRe: EdgeRouter X - only getting 50 - 75% throughput
try:set system offload hwnat enable set firewall options mss-clamp interface-type all set firewall options mss-clamp mss 1492
View ArticleUsing Smart Queue and Basic Queue together?
Background:So, I know this may sound strange to some but I was wondering if Smart Queue and Basic Queue can be used together. In the manual it states; "Note: The Smart Queue feature conflicts with the...
View ArticleRe: Can't block inter-VLAN routing
I might be wrong, but isn't ADDRv4_switch0.40 just the router's address on vlan 40? If that's the case, other IPs on that VLAN aren't blocked. IIRC, you'd need a network-group.I'd actually suggest...
View ArticleEdgeRouter X SFP Power/port Problem
Hi ,I use ER X SFP 5port as a switch with 5 ports every port poe on 24v passive and SFP port as a UPLINK to second ER-X-SFP. Power for ER-X-SFP comes from AC/DC power adapter integrated with baterries...
View ArticleRe: Dual peth WAN - Dual LAN NAT hairpinning
I do have few DNAT rules as can be seen from the config but I don't think it's cutting it. I've taken out the mentioned settings that wizard uses.
View ArticleRe: L2TP server crashes after ~3 hours
MattCarp wrote:We'll see how this goes. I think I still prefer it to OpenVPN. OpenVPN is harder to configure and the lack of a built-in iPhone VPN client makes that side harder, too.IMO, on the...
View Article
