Re: Router Setup Question - No WAN Access on eth2
carlhussey@ubnt:~$ show ip route Codes: K - kernel, C - connected, S - static, R - RIP, B - BGP O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF...
View ArticleRe: Work Aruba Remote Access Point won't connect
I have had that issue with the Aruba RAPs in the past. I had to enable NAT-T option for VPN on the Aruba Controller in order for the RAPs to connect from behind a firewall on a NAT subnet. The only...
View ArticleRe: Emerging Threats Blacklist
Note that the number of addresses/networks (entries) in the ipset is not a factor in performance. With netfilter, the impact is O(n), where n is the number of network prefix lengths in the given ipset....
View ArticlePrinting via the internet to a remote office.
Hi All, I'm new to the Ubiquiti line and have a question for you. We have a main office in NZ and a remote sales office in Australia and would like to be able to print from our NZ system to a Xerox in...
View ArticleRe: Printing via the internet to a remote office.
Yes. If you establish an IPSEC or OpenVPN connection between the two sites you can print from the NZ site to a printer in Australia. The printer would need to have a network interface or would need...
View ArticleRe: Printing via the internet to a remote office.
Thanks for that. The site used to have a server so the printer has a static ip. If the router is capable then it will also be the dhcp server however that isn't important as there are only 2 printers...
View ArticleRe: IPv6 dns servers not returning static-host-mapping hosts
Disabling dhcpv6 dns seems to break youtube on the xbox one (seems like it waits a long time for ipv6 to timeout or fail before it uses ipv4), so I've reenabled it.
View ArticleRe: Problem keeping or restarting IPSEC with Cisco RV180
Hi , You would be better to open a new thread as this is an old thread and your requirements are different. Also, you don't seem to have an EdgeMax anywhere in your setup? These boards are about the...
View ArticleBackup Connection Policies
Is it possible to create policies for when the main internet connection goes down? I'm exploring the idea of having a backup internet connection through a lte modem, however, the plans are quite...
View ArticleRe: Printing via the internet to a remote office.
I'm using an IPSEC VPN myself. Performance is better than OpenVPN.
View ArticleChange PPPoE interface to straight DHCP
Hello all, Our EdgeRouter Lite has a primary wan link setup on eth0 using PPPoE and a second backup/failover link on eth1 using DHCP. Configured originally using the Load Balancing Wizard. In the near...
View ArticleRe: Change PPPoE interface to straight DHCP
I am gong to be dong something similar next week as well. Following along to learn the best option as well.
View ArticleRe: Printing via the internet to a remote office.
I used Google cloud print a few years ago, worked great.
View ArticleRe: IPSEC Nat Traversal Packet Loss
Great not to be alone with that problem. It looks like you are not using PPPoE on any of your connections, so the bug (assuming we are affected by the same) looks like related to the management of...
View ArticleRe: Emerging Threats Blacklist
Hi, Im a bit of a noob, and still learning what is the easiest script to run to implement this, does someone have a step by step thanks
View ArticleRe: Backup Connection Policies
One approach would be combining load-balance and PBR.Prio stuff gets loadbalanced to failover groupNon-prio stuff like guest networks is assigned to primary WAN link only. (create extra routing table...
View ArticleRe: Change PPPoE interface to straight DHCP
Of course you can re-run the wizard, might be fastest if you only made small changes. To build upon current config:Make required changes to the interface, re-apply WAN firewall rules to interface...
View ArticleDHCP issues with dnsmasq
When my router starts up, the DHCP server fails to start with it. /var/log/messags points to an error in dnsmasq-dhcp-config.conf. (It can see the host attached to eth2) Mar 12 23:03:01 erl2001...
View ArticleAllowing traffic from DMZ to LAN
Hi I have my LAN on the eth0 interface and now i have a server on the DMZ, publically accessible now with NGINX I need this server to access various servers on my LAN, but for now, lets just focus on...
View ArticleRe: Router Setup Question - No WAN Access on eth2
You are right, it would have been sudo route -n, but show ip route is even better ...Anyway, this does not clarify the issue, your wan ip address doesn't belong to a 10.0.0.0/24 network ....On the...
View Article
More Pages to Explore .....