Re: ER-X and Unifi UAPs with VLANs
No, you're making it too hard. Let the WAN+2LAN2 wizard configure things as it will - eth0 will be WAN and eth1-4 will be on switch0. Create additional VLAN interfaces on the switch:switch0.10 can be...
View ArticleCan I add VIF to Switch0
Can I add a viritual Interface to Switch0 instead of a physical interface? Exadd ETH2.40 instead of adding ETH2 to SWITCH0.
View ArticleRe: Can I add VIF to Switch0
Yes indeed, and if the port itself is on the switch, I'm not sure adding a vif to it will do anything. set interfaces switch switch0 vif 10 address 192.168.1.1/24and so on. An easy way to see what you...
View ArticleRe: ERX v1.9.1 firmware issue? router locking up hard!
ok. the 1.7 has been up for almost 15 hours. I'll let it run through the week. over the weekend when i have some time, i'll move back to 1.9.1, after saving the and posting my config minus the QoS...
View ArticleInbound Firewall rules with DHCPv6-PD
I wanted to know if anyone else has tried to resolve this issue. I want to implement IPv6 using DHCPv6-PD at home but I also have services at home I would like to access over IPv6. This of course would...
View ArticleRe: Can I add VIF to Switch0
switch switch0 {mtu 1500switch-port {interface eth0 {}interface eth3 {vlan {vid 845}}interface eth4 {vlan {pvid 845}}vlan-aware enable}} I want to swapinterface eth4 vlan pvid845 tointerface eth2.845...
View ArticleRe: Can I add VIF to Switch0
You don't have eth2 on the switch. It appears you removed it.If you don't mind, I'd suggest restoring everything to factory state to make sure there aren't other issues. Then you can add the vif to the...
View ArticleRe: Inbound Firewall rules with DHCPv6-PD
I'm not sure I understand. Why not just set IPv6 firewall rules on the router, and perhaps find an IPv6-friendly dynamic DNS service?
View ArticleWhat does all-ping enable do?
From the online help, it seems to say that this means the router will allow you to ping it from the WAN, but even though it's enabled on my ERX, it won't respond to pings unless I create a firewall...
View ArticleRe: Can I add VIF to Switch0
Thank you! This is what I want to do I guessset interfaces switch switch0 switch-port interface eth2.845 vlan pvid 845Not sure if it is possibleETH2 should NOT be in SWITCH0 becasue it is a routed...
View ArticleRe: Can I add VIF to Switch0
So, you want to make eth2 have a PVID of 845, and eth2 is not on the switch? That's it? I think PVIDs and VLAN tags only apply to switch interfaces - if you're routing then there isn't a need for VLAN...
View ArticleRe: MS PPTP client to far end PPTP server connects, but is very slow
I've tried everything I can think of to fix this. changed offload, created firewall policies to explicitly allow the 1723 traffic to be unhindered etc. Nothing is fixing this. Anyone have any thoughts...
View ArticleRe: One to One Nat and Firewall Config Problems
Ok, I'm not sure what fixed it, but I went back after upgrading the router to 1.9.1 and completely removing the source config section through CLI as opposed to clearing it out in the GUI, and it now...
View ArticleRe: Inbound Firewall rules with DHCPv6-PD
Sorry if I wasn't clear. I was asking primarily about managing the firewall rules since the IPs aren't static but delegated and change.
View ArticleClik here to view.
Re: Open VPN networking is working but no internet access
And now, who is 192.168.1.100 ?
View ArticleRe: CHAP authentication failed - Centurylink Gigabit Fiber
jimkill it's odd since it has been working for me for over 6 months with the same PPPoE and Interface settings. I cannot even get the ERL to work now with the C2100T in bridge mode
View ArticleRe: Help with basic config for Centurylink Gigabit please
have you had any Chap authentication errors? I am in the PNW (portland specifically) and recently CL will not work with my ERL. I have essentially the same basic config as you - vlan 201, pppoe, mss...
View ArticleClik here to view.
Re: Open VPN networking is working but no internet access
sorry I am now confused after so many trial and errors.this is how config looks like.openvpn vtun0 {description OpenVPNencryption aes256hash sha256mode serveropenvpn-option "--push route-gateway...
View ArticleRe: Help with basic config for Centurylink Gigabit please
Can you pull the logs and see what it reporting? Also, whats your MTU set as?
View ArticleRe: Help with basic config for Centurylink Gigabit please
the only log I found is the following (system log tail / gui log monitor). If there is another spot let me know. I started a thread on it here (dont want to hijack) and its interesting that you were...
View Article
