Re: ERLite-3 IPSec VPN throughput issues
Also note that VTI is slower than regular IPsec. GRE/IPsec is faster than VTI, but still slower than reqular IPsec.
View ArticleRe: Easy simple VPN
What is the difference between PPtP and IPSec site-to-site?Given my stated objective of taking a simple WAN+2LAN2 config with one PC on the inside using EdgeOS v1.8.5 and being able to securly remote...
View ArticleRe: AT&T Microcell
Thats what I have, the newer/smaller black Microcell by Cisco. It was working just fine being on Netgear Nighthawk R8500. bweisz wrote:Perhaps you can provide a bit more detail on the problems you are...
View ArticleRe: Can't get dual wan failover only to work
16again wrote: set interfaces ethernet eth1 vif 101 dhcp-options default-route-distance 209Note that tweaking the distance only affects the main routing table. Anything LAN interface that is...
View ArticleRe: L2TP lost ability to route over OSPF with 1.8
For clarification, whan I look at the other routers it does see, via OSPF the distributed 192.168.12.100 but can't route in either direction. The solution just posted did work. I'm curious why it...
View ArticleRe: ERL + ERPro + Interface tunnel GRE and OSPFv3
Try adding tun1 under ospfv3 area 0.0.0.0.
View ArticleERL3 L2TP not responding to port 4500
I have configured my ERL3 after consulting various posts, including the guide here. As shown by the attached tcpdump it responds to the IKE packets but when the client (iPhone ios 9.x) send in the...
View ArticleRe: force load balance back after failover
Hi Stig, thanks for taking the time. 1. I have those weights there because of previous tests. It does not harm to have them there right ? I know in failover there's only one active all the time with...
View ArticleScheduled Reboot every Sunday morning
Hello All, Can I get confirmation that the following code is good to achieve every sunday morning 4:30 reboot of the edge router? Will this automatically update the crontab config file? set system...
View ArticleRe: ERLite-3 IPSec VPN throughput issues
Thanks for the response ! Do you envision that we will see performance improvements via software updates, or are we simply hitting the limit of the SoC? It seems like I am able to reproduce nearly...
View ArticleRe: Edgerouter Lite slow and "Failed WQE allocate" in log
Saved config. Changed to a spare, reset, download config, -same. Disabled DPI, fewer error messages, maybe 1/3. Error messages can be often be caused by high load, fx speedtest. Any takers?
View ArticleRe: Site-to-Site VPN between EdgeRouter Pro 8 and Cisco ASA 5510
Hi and , As of 9:26PM PT, I just tested again before taking an hour break...The ping to the remote host of 72.16.3.218 is again ping-able. Not sure what is causing it to be ping-able at times and...
View ArticleRe: Slow WAN gigabit speeds on ER-X
Thanks all. HW enabled and I see improvement in D/U speed. It jumped from 580Mbps to 670Mbps. It looks like I'll need to pick up ER-Lite to get close to Gb speeds.
View ArticleRe: Edgerouter Lite slow and "Failed WQE allocate" in log
Similar "Failed WQE allocate" symptoms have been discussed...
View ArticleRe: L2TP lost ability to route over OSPF with 1.8
corbywan wrote:... I'm curious why it worked in 1.7 and prior just by adding the L2TP subnet to the Networks section of the OSPF config on the main router, and then it stopped working. An interface...
View ArticleRe: Site-to-Site VPN between EdgeRouter Pro 8 and Cisco ASA 5510
Previous tcpdump: It seems like tcpdump has access to ipsec session keys, so it displays decrypted packets. VPN looks fine now.There might be an issue with ipsec and LB causing only ER LAN interface to...
View ArticleRe: force load balance back after failover
wrote:The modify balance rule is only intended for LAN interfaces, so remove it from switch0.So you mean firewall modify rules really should go on both eth3 and eth4 instead ? Seems counterintuitive...
View ArticleRe: WAN-4LAN for IOT/Kids/Work/Home
Your approach was largely correct. You've not stated which router you have, but I'm guessing one of the ER-X models or an ER-PoE. As long as you set an IP on a different subnet for each LAN port, and...
View ArticleRe: ERL + ERPro + Interface tunnel GRE and OSPFv3
On which router ? On Edge Router Pro, the interface tunnel used to reach the Edge router Lite is tun 3 : EdgeRouter Pro [tun3] <==[IPv6]==> [tun1] EdgeRouter Lite
View ArticleEdgepoint POE power?
Hi,I can't seem to find what the max POE output is for the EP-R8?I'm thinking of using the VDC terminal connected to +48V.I would like to power the following equipment. 1x AF241x AF5X4x R5AC Prism Kind...
View Article