Re: Edgerouter X as a VLAN aware switch - 'forward' VLANs?
Thank you again for your replies! I cannot try this at the moment, but wanted some assurance before bying more hardware. I take it as per the example image above, you can forward VLANs 9,10,11 from...
View Articleconnecting to WAN causes disconnect
I have a ERPoE5. I used the wizard to set up WAN+2LAN2. I can connect locally via eth2-4 ports to the ER. But when I connect the ER to my cablemodem, I lose connection to the ER. I have no WAN...
View ArticleRe: connecting to WAN causes disconnect
Maybe your cable modem already does does NAT and DHCP , and you end up with multiple addresses on ER in same subnet. Try changing IP address on LAN port before connecting the cable modem. (re-run...
View ArticleRe: connecting to WAN causes disconnect
I don't understand what you mean by 'disconnection'. When you configure 'WAN-to-LAN', you should entersettings for both WAN and LAN. Typically for a CATVmodem, you use DHCP for its [WAN] setting; the...
View ArticleRe: OpenVPN site-to-site tunnel - ERLite to ERLite - best vpn throughput...
So as promised, I tried this test. The results were..interesting.... Edgerouter lite directly connected to Edgerouterlite (keep in mind this is megaBYTES per second not megabits) were: OpenVPN tunnel:...
View ArticleCopy config via console port
I am connected to EdgeRouter Lite via the console port and a FTDI usb serial cable. I am using Putty and am successful logging into the router and use CLI. I want to copy the config file to my...
View ArticleTwo ERPOE-5s: one creates a PPTP interface, the other doesn't.
I have two ERPOE-5s sitting on my desk right now that I'm trying to set up for PPTP VPN access, and there's some odd behaviour on one that isn't happening on the other. Both are running firmware...
View Article1 ISP, 2 DHCP IP's on different subnets
My ISP provides 2 DHCP IP's on different subnets. I use 2 consumer routers to connect to a mini switch that in turn connects to cable modem. One router serves home devices...
View Articlecellphone cannot reach or pickup my file server
My Network Setup: ERlite-3 and unifi APMy router is setup wlan+2lan2(eth1-10.0.1.0/24, eth2-10.0.2.0/24) my AP is directly connected to eth1(1.0) and a netgear swith on eth2(2.0) my file server and...
View ArticleRe: Copy config via console port
Normally this is done via zmodem but as it seems the package is not installed on the router by default. You could get it via apt-get but I'm guessing no Internet for you since you're working via...
View ArticleER-L static route not followed
Hi folks - I am new to the ER and haven't got my head around CLI yet, so be patient! I have two routers in use, the new ER-L (A) (replacing an old box) and one with a legacy VPN in place (B). When a...
View ArticleRe: connecting to WAN causes disconnect
that was the problem. apparently the default ER 192.168.x.x address was the same used by the cable modem. Switched it to another IP address and it works.
View ArticleRe: cellphone cannot reach or pickup my file server
It could be a few things - sometimes a device's internal firewall don't trust network traffic from a different subnet, sometimes things like file servers use broadcast traffic that is not broadcast...
View ArticleRe: Block mac address
ke it back apparently if im on PPPOE it doesnt work if im on dhcp to the ONT than it does...so weird..i see the DHCP server leasing IP to the boes still yet i can see in the stats that the rules are...
View ArticleRe: Task Scheduler + Ad Block
I'm sure you resolved this issue since it's a year old, but since I can't find it documented anywhere I'll document how I did this. Go to system / task-scheduler / taskAdd a new task named...
View ArticleIPSec VPN Problem
I have a simple IPSec VPN setup between a remote site using an ER-X and an old Cisco router (soon to be replaced so I can use OpenVPN instead). I have used the GUI to set up the VPN. I could get the...
View ArticleClik here to view.
Re: Firewall dropped 443 ipv6 traffic
Also seeing this (also from the facebook CDN) - my firewall for IPv6 is pretty simple, and like you said it should be hitting the established rule. I tried playing with the "system conntrack" settings...
View ArticleRe: Block mac address
A wizard like these for mac would be greathttp://community.ubnt.com/t5/EdgeMAX-Beta/List-of-community-contributed-feature-wizards/m-p/1524500#U1524500
View ArticleFail-over VLAN to 2WAN + VLAN to 1WAN
Hello, I need some help to setup an edge router PoE.I got 2 modems. WAN1 on eth0 WAN2 on eth1 LAN on eth2 I’m looking setup a failover bridge for a staff VLAN from eth0 to eth1 with a dhcp server on...
View Article