Re: Unable to get ip address connected to wifi after setting up vlan on...
I added the vlan to switch and i was able to get the ip address but now I can't get out to the internet. I am able to get out to the internet on the main vlan 1 but vlan 3 i am unable to here is the...
View ArticleNetwork is having contstant blips/pauses/drops/hesitation - please help
Hi all, Very frustrating problem that I have been spending all day trying to solve. My network/internet has been having contstant blips/pauses for the last 2 days. I'm at a loss and could use some...
View ArticleER-8 Configuration
I want to program an ER-8 like the diagram attached, I have not been able to get the LAN to talk to LAN2 or LAN3. Any help I can get would be greatly apprectiated.
View ArticleClik here to view.
Re: Network is having contstant blips/pauses/drops/hesitation - please help
How sure are you that it's not the Internet service itself? Be sure to upgrade to the latest firmware. Perhaps you cando some ping tests to determine where the dropout starts. Dave
View ArticleRe: Network is having contstant blips/pauses/drops/hesitation - please help
Thanks I haven't had and ISP issue in 2-3 years, so to have it happen within days of a router change would be unlikely During this change I upgrades to the latest firmware I'm not sure how to do ping...
View ArticleRe: Monthly Data Usage Chart?
I see that it talks about a negative impact on ERL/ER-POE Routers. Is the same true for ER-X Advanced?
View ArticleRe: Edgerouter lite using PPPOE will not use WAN IP for Proxy
I found the issue. The perl modules that "check" system IP's require an IP with a CIDR notation in order to be considered a "system address". PPPOE interfaces in the edgerouter will not produce a...
View ArticleClik here to view.
Re: restarting BGP
this is why you'd likely want to restart bgpd imish invoked oom-killer: gfp_mask=0x200da, order=0, oom_score_adj=0CPU: 0 PID: 1971 Comm: imish Tainted: P O 3.10.20-UBNT #1Stack : ffffffffc0760000...
View ArticleRe: restarting BGP
actually I am wrong. The daemon comes back up but with no config. Fail....Is there any way to 'replay' the config without removing/replacing or rebooting?
View ArticleRe: EdgeRouter Pro - RAM Upgrade
Same problem here! Are there different hardware revisions of the ER8 Pro's? Someone else already reported success with these ones.
View ArticleRe: Port Forward to a Domain Name
UBNT-stig is right about being computationally expensive for such feature to exist in Netfilter - Linux's firewall and NAT. An alternative solution is to make use of ipset with an address-set. Use the...
View ArticleRe: Dual-WAN router with the following:
There is a company making rack mount kits for the ErgeMax Lite, ISP Supplies is selling it:http://www.ispsupplies.com/brands/wg-AM3G18-120-K/KAM-Fab-UB-RM1.html So you could rackmount the ERLite as...
View ArticleRe: restarting BGP
bbabich wrote:@dragon2611 actually I am wrong. The daemon comes back up but with no config. Fail....Is there any way to 'replay' the config without removing/replacing or rebooting?configure save delete...
View ArticleRe: Edgerouter Pro / Carrier SFP+ When is it out?
Hi. O Yes it is, Ubiquiti are working on a new modell, and it´s that launch date i´m fishing for!
View ArticleRe: Routing locally originated traffic after failover in 1.9.0
Ok, I researched some more. There is a confusing array of behavior for different protocols when lb-local is set to enable or disable, so I made a table of what I found. In the table, eth3 and eth4 are...
View ArticleRe: ATT IPv6 6rd with Pace 5268AC and ER X: Help needed for 6rd IPv6 setup
I'm not sure - but may be you have to set set firewall options mss-clamp6 interface-type tun set firewall options mss-clamp6 mss 1412I had to do this on an pppoe connection.
View ArticleIPv6, dhcpv6-pd and VLANs
Hi all I have a problem with IPv6 on a VLAN interface. Hopefully anyone can help me out here...My setup in short:- WAN: eth5.11 (pppoe 0)- LAN: eth0- LAN Wifi_Guest: eth0.201 All IPv6 config is working...
View ArticleRe: [ERL-3 1.9.0] No DHCP leases since switching to DNSMasq
I had done that. Seems like something in Ungoogled Chromium is the problem. Worked with Firefox, sorry for troubling you guys!
View ArticleModified script for showing dnsmasq's DHCP leases
Unfortunately ullbergm's script parses a file that's also empty on my router, so I changed it to parse /var/run/dnsmasq-dhcp.leases instead, which has less and a little different information. Also I...
View Article