Redirect subdomain to internal IP and Port
Hello,I'm looking to redirect different subdomains to different ports on my server but I'm running into a bit of an issue with the port 80 to 443 automatic redirect. What I'm trying to acheive is:...
View ArticleRe: L2TP not responding externally
Had the same issue on my network .. fix was to disable Back to My Mac on any Mac's since UPNP2 would override any port forwards I had setup and let the Mac have the port. Disabled it on the Mac and...
View ArticleBrand new Edgerouter Lite won't issue DHCP
Hi Folks, I'm trying to access my new Edgerouter Lite (ER-Lite 3). I'm plugged into eth1 with my MacBook Pro. I have a solid green on the console port and mostly solid green with occasional blinking on...
View ArticleRe: Brand new Edgerouter Lite won't issue DHCP
See page 7 of the Quick Start Guide (it should be in the box). You need to use eth0 for initial configuration. After you connect upgrade to latest 1.9.0 firmware. Get it from HERE.
View ArticleRe: Brand new Edgerouter Lite won't issue DHCP
Thanks, but as I said, I've tried all three ports. I'm currently plugged into eth0 and I'm still not drawing an IP.
View ArticleRe: Brand new Edgerouter Lite won't issue DHCP
As per the quick guide, there's no DHCP enabled on eth0 (nor other port). You need to set your PC to static IP.
View ArticleRe: Brand new Edgerouter Lite won't issue DHCP
Ach!! How on earth did I miss that line? I saw the "open a browser and point it to..." line and totally missed the line above it. I even tried the static IP setting, but by that time I'd moved to the...
View ArticleRe: Traffic Analysis not showing some traffic?
, i'm confused... I thought at some point back the traffic analysis ONLY saw offloaded traffic and then in v1.8 or so the ability to see non-offloaded traffic was added. Maybe I'm thinking of the...
View ArticleRe: clear logs
So apparently doing this was a really stupid idea because I used that sudo command and deleted the logs and not I can't pull up any system logs. Any way someone can share the command to recreate these...
View ArticleRe: Two WANs with dynamic IPs and two LANs
I've tried different firmware versions, I'm currently on 1.9.0. I've factory defaulted the router multiple times. The speed is fine when I use only one link. The moment I connect the second line and I...
View ArticleRe: Load Balance Test Script
In your script, if I'm reading it correctly, you're doing 3 pings and calculating average.Ping already gives your average, all you have to is extract it. admin@router-brano:~$ /bin/ping -n -c1 -W1 -w1...
View ArticleRe: Port forwareding on an ERPOE-5 - external port different than internal
Just as you would translate an address you can translate a port in the same rule. Without seeing your NAT config there is little anyone can do to help. Make the modifcations and post your config. Not...
View ArticleClik here to view.
Re: Load Balance Test Script
You are very much correct. When exhausted I do things the hard way
View ArticleEdgeMax unable to block StreamingMedia
Hello, I have an EdgeRouter-X with firmware 1.9.0 installed on it. Recently my son's Chromebook that he received from school has QUIC enabled on it. As a result, the Firewall Policy that I have set up...
View ArticleCan't access Edgerouter PoE-5- crashed
Tonight, after I create a VLan, during the process of saving it, the router booted me out and now I can't access it. I have it setup as: eth0-WAN, eth1-PoE(AP AC-Pro), rest part of switch0. I don't...
View ArticleRe: Blocking IPv6 traffic to Netflix over HE.net tunnel
Thank you for the example. I rarely change my configuration, so it always takes some time to figure out how to do it. I had to use another address (mine was on 2a01:578:3::/48), so to be sure I put...
View ArticleClik here to view.
2 IPSEC VTI 2 tunnels through NAT - can it work?
Hi Everyone - I have started playing around with a configuration 'in the lab' to do this, but one thing I can't easily simulate (and don't fully understand, to be honest) is whether what I am trying in...
View Article