Re: Is it possible to use IPv4 PPPoE and IPv6 IPoE on one server?
I found a way to achieve what I want. EdgeRouter - Policy-based routing (source address based) – Ubiquiti Networks Support and Help CenterI added an IP alias to my home server.From one IP address, my...
View ArticleRe: WAN Load-Balance and L2TP-over-IPsec - remote network does't respond via...
Thank you, If you need additional information, i can post here.
View ArticleRe: outbound port translation port 25 to 2525
You need to add a dNAT rule, incoming interface=lan-interface , destination-port=25 , destination-address=YourSMTPserver inside-port=2525 , inside-address=YourSMTPserver Or in your smtp software ,...
View ArticleOption 43 DHCP for APC Network Card
I am trying to get a used APC Network card to take an IP address from my EdgeRouter via Option 43 - it needs this enabled.From the APC website for the AP9617 card: Vendor Specific Information - (option...
View ArticleRe: VPN (static) route issue
The load balance group is used for wan failover, what do you mean I'm not using it anyway?I've tried that already. I read about that causing issues sometimes, but I've verified that all ipsec packets...
View ArticleExclude some traffic from OpenVPN
Hello, i would like to exclude some traffic from my OpenVPN connection. The router (EdgeRouter x) is set up as an OpenVPN client (and this is working), but i want to bypass the VPN for some traffic...
View ArticleRe: VPN (static) route issue
I stand corrected. I removed the load balance and it's working perfectly with 3 non-vti tunnels now. I need this load balance group for WAN failover, so I will troubleshoot this further now that I know...
View ArticleRe: Dual Gigabit WAN and ER-5 POE
I believe there's a bit of a performance hit when removing eth2/3/4 from switch0 to use the as separate interfaces (not really a hardware offload issue). If you really need the three networks, it may...
View ArticleRe: VPN (static) route issue
re-enabled load-balance for wan failover only.vpn pings stopped as expected.set lb-local disablevpn can still not ping. If I remove the entire load balance, the vpn works perfectly. I need that...
View ArticleRe: ERX set e0 to 1000/full?
What he said. I'll just add that you can't force 1000/full, it has to be auto negotiated.
View ArticleRe: Dual Gigabit WAN and ER-5 POE
I don't really care about hitting more than 400 Mb on eth3 and 4. Will assigning eth2 alone to switch0 and reconfiguring all the settings to use switch0 instead of eth2 enough to fix the problem?
View ArticleIPSEC VPN tunnel question?
Quick question... I have about 6 edgerouter's that are configured using IPSEC VPN tunnel's, though not all connected together. - Group A has 2 that are connected for a family ag business- Group B has...
View ArticleRe: ERX set e0 to 1000/full?
And there's no need for Cat6 either - Cat5e is just fine for GigE - we have hundreds of devices across our network running Gigabit FD and none of them use Cat6 cable even with 300 fut cable runs...Jim
View ArticleRe: EdgeMax rescue kit (now you can reinstall EdgeOS from scratch)
While I haven't noticed any problems with the flash drive in my ERPOE-5, I've decided that I ought to image the drive, just in case. Here's how I'm doing it (it's being transferred as I write this): On...
View ArticleRe: VPN (static) route issue
Do you also need the VPN tunnels fail over? It can be done but requires additional scripting. I have VPN with fail-over configured, but in fail-over mode I'm not failing the VPN, only Internet.
View ArticleRe: VPN (static) route issue
No I don't need VPN failover. The VPNs can just run on the main WAN and that will be fine. The backup WAN is so slow it's just for emercengies anyway. Really just a way to get into the site remotely...
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X
is this thread still being tracked at UBNT? I think we've got enough users that experience this that you could be collecting a lot of data from them to track down the cause of the issue. Thanks!
View ArticleRe: VPN (static) route issue
I have that config running, can post it sometime later this weekend ...need to sanitize it first.
View ArticleRe: VPN (static) route issue
You're not having any firewall modify rules in config you posted.That's what I meant by "you're not using it" ...as loadbalance was intended to be used.
View Article