Re: RRAS site-to-site
Ok it turns out I need to initiate the connection from my RRAS server before getting any logs. here is what I get when I initiate the connection from the RRAS: 02[NET] sending packet: from...
View ArticleRe: pixelserv dnat not working
nat rule 1 seems disfunctional. Double check address-group ADS-A Also, command below will show how many times NAT rule has been hitsudo iptables -t nat -L -v
View Articleoutbound port translation port 25 to 2525
I have a ATT fiber and they block outbound port 25 so I can't send out email to my smtp relay server. I would like to take outbound smtp data (port 25) and change to port 2525 that is not blocked. I...
View ArticleRe: restarting OpenVPN tunnel
Actually, no need. I think this works if the tunnel goes down.
View ArticleRe: ERX set e0 to 1000/full?
Usually if auto doesn't do it then there's something physically wrong. First thing to try is a different cable between the router and the ISP connection. Make sure it's a Cat-6 cable. -- Pete
View ArticleRe: EdgeRouter dashboard doesn't work with Safari
Same problem here with mac os 10.12.4. Anyone have suggestions?
View ArticleRe: L2TP/IPSec VPN Connection Disconnects after a few seconds.
I looked in my log and found the following. This is happening about every 10 minutes...the same interval that my eth0 drops out in the logs above. It also references my OpenVPN tunnel, which does drop...
View ArticleRe: directv dvr's not getting IP addresses after update to 1.9.1.1 er-x
the technology you refer to is called MoCA...kind of interesting actually http://www.mocainyourhouse.com Sounds like something within the new firmware not playing nice with the adapter?
View ArticleRe: L2TP/IPSec VPN Connection Disconnects after a few seconds.
Kind of working through this, self-troubleshooting as I go. I found this article where someone had something similar, and weirdly enough MTU settings and firewall descriptions (??) seemed to fix it....
View ArticleRe: directv dvr's not getting IP addresses after update to 1.9.1.1 er-x
I might have foobared the upgrade. i'll try again tonight when the dvr's and network are free. i'll report back.
View ArticleRe: L2TP/IPSec VPN Connection Disconnects after a few seconds.
Tried the suggested solution on the article above...added descriptions to all firewall rules (still felt like a longshot) and changed MTU to 1400. Here's what I see. Still no go: May 19 19:40:13 erx...
View ArticleRe: Help setting up NetFlow
I just set this up (ManageEngine NetFlow Analyzer) and am finishing the config now.
View ArticleRe: outbound port translation port 25 to 2525
If your smtp relay server supports connections on port 2525, can't you just set your email sending client to use port 2525? Or you could use port 587, which is supported by many mail servers as an...
View ArticleEdge Router Pro and BGP setup in datacenter
I purchased an Edge Router Pro (ERP) with the intention to install it in a datacenter (DC) in front of a dedicated server. My existing experience at the DC is with an ipcop as a router and static ip...
View ArticleRe: Edge Router Pro and BGP setup in datacenter
This forum has several threads on BGP on the EdgeRouter. I've been running it for years. Just search for BGP. There are some succesful configs listed out on the forum too.
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X
I too had no luck with hwnat enabled - Arris SB6183, Comcast Business 50/10, ER-X v1.9.1.1. Disabled hwnat, rebooted, and IPv6 came up immediately.
View ArticleUnable to resolve external IP using domain name
I've recently migrated our home network from a consumer router (asus ac68u) to an EdgeRouter X plus UniFi UAP-AC-PRO. I did a lot of reading ahead of time, and luckily the migration went smoothly....
View Article
More Pages to Explore .....