Re: zone firewall slow?
Ive been trying to use ACL firewall in this manner: 1. allow est/rel on all interfaces (but it seems as if i gotta specify this over and over for EACH ruleset)2. allow in-interface=.. out-interface=.....
View ArticleER-X and Unifi UAP-AC-LITE - want to delay AP startup
I have a very basic setup with an ER-X (1.8.5) and UAP-AC-Lite: ER-X Port 0: WAN inER-X Port 4: Unifi UAP-AC-LITE via a POE adapter --- (so AP is not powered POE through ER-X; ERX is also on own...
View ArticleRe: ER-X and Unifi UAP-AC-LITE - want to delay AP startup
Can you be more clear about how it's all powered; Is the router powered through PoE on eth0 with passthrough enabled on eth4, or do you have the router powered by the included wall wart with the AP...
View ArticleRe: ER-X and Unifi UAP-AC-LITE - want to delay AP startup
WAN modem --> PoE injector LAN port | PoE port --> ER-X eth0 | eth4 --> UAP
View ArticleRe: Assigning IPv6 DNS servers to clients via DHCPv6?
Changed to dhcpv6-stateless. Here's radvd.conf: # cat /etc/radvd.conf interface eth0.102 { # This section was automatically generated by the Vyatta # configuration sub-system. Do not edit it. # #...
View ArticleRe: ER-X and Unifi UAP-AC-LITE - want to delay AP startup
Maybe an update to the bootloader will resolve this issue:UpdateCheckVersion
View ArticleRe: Assigning IPv6 DNS servers to clients via DHCPv6?
"dns forwarding" now looks like this: forwarding { cache-size 1000 listen-on eth0 options enable-ra options dhcp-range=::,constructor:eth0,ra-stateless options...
View ArticleRe: ER-X and Unifi UAP-AC-LITE - want to delay AP startup
Thanks. Right now the ERX is powered by the supplied wall-wart, while the Unifi AP is powered by the supplied 24v 0.5a POE injector in between the ERX and AP: WAN=>ERX (wallwart) => PoE => AP...
View ArticleRe: ER-X and Unifi UAP-AC-LITE - want to delay AP startup
It works fine with the AC-Lite, can't speak first-hand to the other models.
View ArticleOne cpe staton one Edge point r6, 5 subscribers?
Hello guys. I recently deployed my first r6 as a switch with a custom 24v ups. We liked it. Now on I have the following situation, and would like to know if it is feasible or I'm I dreaming. In in a...
View ArticleRe: Setting L2TP VPN
I tried that, but is still not working. Remember that I have my ISP router above the EdgeMax router, so the EdgeMax Wan is a static address.Thanks
View ArticleRe: Routed IPTV
Thank you for your responses. Unfortunately the suggested script didn't solve this issue. Both ports eth0 and eth0.4 get the correct IP-addresses, even without the script. The DHCP server of the...
View Articleusing static DHCP mapping for DNS lookup & changing the static mapping name
Hi I use a lot of static mac/ip mappings for my DHCP server on my ErLite. Now, the DHCP returns a domain name, and what I'd like is to be able to use that static mapping name, append the domain name of...
View ArticleClik here to view.
Re: ERL was fast but not is very slow - Centurylink says its my issue
I yanked my ERL and hooked up a TP-Link C2600 router that supports VLAN tagging to the ONT and can now get a full 970Mbps. Either the ERL cannot support the speeds (unlikely as others are getting near...
View ArticleRe: Mutiple VLANs with VPN
ardiross wrote:I wasn't able to enter that command. I received the following error: Firewall config error: action 'modify' requires more specific configuration under the 'modify node.I assume that...
View ArticleRe: Update to 1.9 broke my l2tp/ipsec
It was also my case.I messed (randomly) with a lot of settings like nat-t, allowed subnets...etc. maybe that also made it work.When i say messed around it may mean literaly erase that...
View ArticleER-Poe5 ipsec hardware offload not working
I have an er-poe5 with ipsec site to site vpn to another edgerouter lite. It seems like the hw-offload dosent work because when I transfer files over the link I get max 5MB/sec and the cpu is running...
View ArticleIs a static route the solution?
Dear expertsWhile I'm actually a software engineer and not a network engineer, I'm requesting your help. :-)Setup:- Router 1, connected to my ISP (WAN) 192.168.192.1/24- Switch, port based VLAN- Router...
View ArticleRe: 1.9.0 broke dashboard for me (using Firefox)
Same problem with my ER-POE, browsing with safari on an ipad shows TBD and no graphs, atomic web browser on the same platform shows the dashboard correctly. On PC Firefox has the same issues.
View ArticleRe: Assigning IPv6 DNS servers to clients via DHCPv6?
Wow, I'm shocked that it still doesn't work. When I configured DNSMasq, my clients received their DNS servers as quickly as they received their IPv6 addresses. And I used different servers from my...
View Article