Re: Error Upgrading the System
I have seen similar issues as well and I was able to upgrade from 1.2 to 1.3 via the web interface, and then jump straight up to 1.9. I do wonder why Ubiquiti ship routers (even in 2017) with a 2013...
View ArticleRe: No 'wizard' tab in new Edge Router Lite?
I have seen similar issues as well and I was able to upgrade from 1.2 to 1.3 via the web interface, and then jump straight up to 1.9. I do wonder why Ubiquiti ship routers (even in 2017) with a 2013...
View ArticleRe: Beta access not working
Hi David, same with my accout no access to unifi Beta. Thanks
View ArticleRe: Do OpenVPN files remain after a reset?
I often upgrade the system image of my EdgeRouters installed 'around' via cli and while connected through VPN, the content of the /config folder is kept as is, is even stated in the help article.See...
View ArticleRe: How to correctly configure hyperV and Edge router networking
Everything I am reading says it should be working, but its not. I have tried enabled just VLAN tagging in the physical nic properties (instead of priority & vlan) and I also tried setting...
View ArticleRe: Change TTL on Edge Router Lite
I cant get this to work in 1.9.x FW. Were you ever able to get this working?
View ArticleRe: NAT setup for 2WAN+2LAN
The wizard fails to work for this setup. As far as I can tell I need create the rules manually with dNAT and firewall. I'll report back if I have any troubles. Thank you for your help 16again!
View ArticleRe: Do OpenVPN files remain after a reset?
Thanks, that's important. I guess I'll have to add instructions to go back and wipe the old files so they aren't there.
View ArticleRe: Modify TTL
The EdgeOS framework on top of iptables don't let you alter the TTL value, so you have to add it manually. use a custom script that checks iptables rules, and if your rule isn't detected, add it....
View ArticleRe: EdgeRouter X SFP - Trunk port
Seems like I swapped 101 and 102, swap them back (on all lines) On eth5 , you don't need to configure vif102, as eth5 is under the switch, so its IP config goes under "switch0 vif102" If VLAN101 is a...
View ArticleRe: Modify TTL
Well the really weird thing is when I add it, it never shows up in iptalbes rules (iptables -S or -L). The add command doesnt generate an error. It just never shows up and doesnt take effect. Thanks...
View ArticleRe: No 'wizard' tab in new Edge Router Lite?
techsapiens wrote:I have seen similar issues as well and I was able to upgrade from 1.2 to 1.3 via the web interface, and then jump straight up to 1.9. I do wonder why Ubiquiti ship routers (even in...
View ArticleRe: No 'wizard' tab in new Edge Router Lite?
You have to go from 1.2 to 1.4 then to the latest
View ArticleRe: How to correctly configure hyperV and Edge router networking
Updating drivers did not help.If anyone has any other ideas it would be much appreciated because I am really struggling now.....
View ArticleRe: How to correctly configure hyperV and Edge router networking
Do you have any other equipment that can handle vlans? This way you can see which device isn't working Use wireshark on eth1 too see vlan tags.
View ArticleRe: Feature Wizard for Zone Initialization
Does it give an error. I only use this to initialize my routers. If you already have firewall definitions bound to interfaces, you may have issues. It does work on 1.9.1, and 1.9.1.1. I just used...
View ArticleRe: EdgeRouter X SFP - Trunk port
I can't get this to work. I have to use bridge to get IPTV to work, but bridging takes a big hit on performance and my TV often laggs when there's a lot of traffic on the network. It seems like if I'm...
View ArticleRe: EdgeRouter X SFP - Trunk port
A bridge is a software switch, if that does work, a hardware bridge (like we created with vlanson sw0) should work too.
View ArticleRe: EdgeRouter X SFP - Trunk port
That's good news!Thank you so much for helping me. Here's my network settings the way I have been using the router the last 6 months: firewall {all-ping enablebroadcast-ping...
View Article
More Pages to Explore .....