Re: Route Public IP to Client for Wisp
ubnt@ubnt:~$ show configuration allfirewall {all-ping enablebroadcast-ping disableipv6-receive-redirects disableipv6-src-route disableip-src-route disablelog-martians enablename WAN_IN {default-action...
View ArticleRe: PPTP/L2TP IPSec Site-2-Site - routing problem
I upgraded the firmware to 1.9.1, hoping for improvements regarding routing from the release notes. But my hoping were not fulfilled. If PPTP/L2TP is used with load-balancing and pppoe interfaces, a...
View ArticleRe: DHCPv6-PD
Do you see anything 'interesting' with the show firewall ipv6-name WANv6_LOCAL statistics command? Any dropped packets? I'm not sure if a tcpdump is before or after filtering by the firewall so perhaps...
View ArticleRe: Routed subnet
Thing you may run into is that if you want to host things, the traffic won't make it to your server(s), since the ISP has a different route set on their end to get traffic there ...
View ArticleRe: Multiple WAN issues
your issue is most likely caused by the ER-5 really being an ERL with a permanently attached switch ... so there are some issues when trying to use the switched ports as routed ports. It's not the same...
View ArticleRe: DHCPv6-PD
With those changes, but still a /56 prefix.sudo tcpdump -vn -r /tmp/eth0_dhcpv6.pcap reading from file /tmp/eth0_dhcpv6.pcap, link-type EN10MB (Ethernet) 12:17:11.221608 IP6 (hlim 1, next-header UDP...
View ArticleRe: DHCPv6-PD
At this point, I think the Charter rep I spoke to was full of *&$@ and IPv6 has not rolled out to my area yet.
View ArticleRe: Why can not I see the ip of my camera by the GUI ?
If the graphical interface does not allow to see the network, is it possible to install this program?Https://doc.ubuntu-fr.org/autoscanIf yes, how ?With detailed explanations please.
View ArticleRe: DHCPv6-PD
Maybe... but there's plenty of ICMPv6 hits in the firewall statistics so maybe not. Let's change the capture to sudo tcpdump -n -i eth0 ip6 -w /tmp/eth0-ipv6.pcap and check what we see with that. Regards
View ArticleRe: Routed subnet
put the /28 on your WAN interface, as the ISP intended or see if they do routed subnets.
View ArticleRe: Why can not I see the ip of my camera by the GUI ?
If the graphical interface does not allow to see the network, is it possible to install this program?Https://doc.ubuntu-fr.org/autoscanIf yes, how ?With detailed explanations please....
View ArticleRe: DHCPv6-PD
Same command to read it right? If so, this is the output.sudo tcpdump -vn -r /tmp/eth0_dhcpv6.pcap reading from file /tmp/eth0_dhcpv6.pcap, link-type EN10MB (Ethernet) 12:19:52.601206 IP6 (hlim 1,...
View ArticleRe: DHCPv6-PD
Same command to read it, but if you copied and pasted the tcpdump command from my last post, note that I changed the file name that the capture was saved to. Are you reading from the correct file?...
View ArticleRe: DHCPv6-PD
Didn't notice that, here is the right file.sudo tcpdump -vn -r /tmp/eth0-ipv6.pcap reading from file /tmp/eth0-ipv6.pcap, link-type EN10MB (Ethernet) 12:37:21.051720 IP6 (hlim 255, next-header ICMPv6...
View ArticleRe: OPENVPN client
I followed this instruction and I am able to establish a tunnel from my Edgemax to a remote router. However, I am unable to ping computers on either direction. Could someone tell me what I need to do...
View ArticleRe: PPTP/L2TP IPSec Site-2-Site - routing problem
I did a quick and dirty fix for this with a simple extension to the /etc/ppp/ip-up script. To who it may concern, I put this on the end of the script. This will look for the defined local address of...
View ArticleRe: DHCPv6-PD
So there's a router running IPv6 there as we can see the ICMPv6 Router Advertisements (RA). The other point in the RA are the flags which are 'Flags [managed, other stateful]'. This is the router...
View ArticleHelp with upgrading firmware 1.2.1
I have a ER lite that has firmware 1.2.1 on it. I have tried to upgrade the firmware via the GUI and it fails. I have searched for the instructions to do this via CLI but from what I have read, it...
View ArticleRe: Hairpin NAT not working since 1.6.0 > 1.9.0 upgrade
I've sinced changed my config and broke the hairpin NAT. So i have stopped using the port forward and created individual masquerade nats for each port being forwarded. So each port gets two nats... one...
View Article
More Pages to Explore .....