Re: 2 WAN 3 VLANs without load balance and failover
Yes, hosts connected to switch0 (192.168.10.0/24) use only eth0 as Wan interface.I can't test vif 20 and vif 30. Vif 20 should use eth1 as a WAN interface. Thanks!Thomas
View ArticleRe: Edgerouter X New Setup Security
If your provider is only providing you an IPv4 address and IPv4 service, then the IPv6 isn't needed -- no need to configure it. Otherwise, you can see what it would like like see this post.
View ArticleRe: Edgerouter X New Setup Security
Good point, no ipv6 is being used so it's moot. Thanks for the help!
View ArticleConfig help: Firewall modify / marking packets not working or detected by...
Hi! I'm trying to learn how to set up QoS so that I get bandwidth priority to the game League of Legends. I've mostly followed what I can glean from this post as reference:...
View ArticleRe: Release: WireGuard for EdgeRouter
Try removing, reinstalling the package and rebooting.The error suggests the kernel module isn't loaded.
View ArticleRe: How to configure an ER Infinity to be L2TP CLIENT
no one from ubnt going to answer this?
View ArticleRe: ER12 Can't connect to it on my computer.
Thanks man. Overlooked the obvious. Turned off the Firewalls, used FireFox, and I'm up and running. I appreciate you taking the time to respond. Cheers!
View ArticleRe: Can't log into Edgerouter X
Did you change you password the last time you were able to log in? I always verify that I can login from another putty session while I am still logged in from the session I changed the password from....
View ArticleRe: Config help: Firewall modify / marking packets not working or detected by...
Did you apply the modify ruleset to an interface?What's the output of:show firewall modify lolports statistics btw: You could play around with ceiling value, afaik , when unspecified, ceiling is set...
View ArticleRe: Anycast Routing
For anycast, there is nothing to configure, it relies on normal routing. And hosts , like 8.8.8.8, being advertised from multiple locations, and the rest of the internet choses closest BGP path to...
View ArticleRe: POLICY BASED ROUTING USING DESTINATION PORT
wrote:Biggest cotcha: applying firewall modify rule should be:set interfaces switch switch0 firewall in modify FTPMoreover, you're using rule number 21, this is unrelated to ftp being port 21. (but...
View ArticleI think I broke it. CA.pl doesn't exist
Hey Long time Unifi user, relatively new Protect user with G2 Plus, and have now replaced my aging Asus router with an ER4. My only requirement is to setup an OpenVPN server which I used on my Asus,...
View ArticleRe: Config help: Firewall modify / marking packets not working or detected by...
wrote:Did you apply the modify ruleset to an interface?What's the output of:show firewall modify lolports statistics btw: You could play around with ceiling value, afaik , when unspecified, ceiling...
View ArticleRe: Release: WireGuard for EdgeRouter
I agree with 's advice and please make sure you are using the wireguard-v2.0-e100-0.0.20190406-1.deb package for eOS v2 package. I was testing V2.0.3 on my ERL last evening and ran into a similar...
View ArticleRe: EdgePoint R6 switch configuration
wrote:When doing what i said above i found "set interfaces switch switch0 switch-port vlan-aware enable" which is not in my configuration. When i tried to do that it saidThe specified configuration...
View ArticleRe: I think I broke it. CA.pl doesn't exist
From the ls output that file is missing along with some others. Install the firmware using; system add image https://dl.ubnt.com/firmwares/edgemax/v2.0.x/ER-e300.v2.0.1.5174690.tarReboot and you should...
View ArticleEdgeOS log-modes in ipsec vpn configuration
EdgeRouter X 2.0.1 I have enabled the following log-modes in the ipsec site-to-site configuration: log-level 2 log-modes ike log-modes net log-modes enc log-modes asn log-modes mgr log-modes job...
View ArticleRe: Determine which access point device is connected to
If you /sbin/switch without any command, it will display the only available documentation. other interesting commands /sbin/switch /sbin/switch vlan dump /sbin/switch pvid dumpHere's output on a fresh...
View Article