Re: Backing up ERPro-8 for failover.
Okay ran that on the routers. The non public facing router has this:(put as a gist as these lists were long) Outward facing router:https://gist.github.com/codejoy/5ad53447bbc4d9ca3bf70dd4965cd0e0...
View ArticleRe: 2 WAN 3 VLANs without load balance and failover
Hi Jonatha,Thank you for your response. I assume that these tasks cannot be done through the GUI. So I'm going to study how to do it with CLI. Where will it be better to create VLANs on an Ethernet...
View ArticleRe: Which Edge ?
Thanks you for that. I suspect ER-4 will do for me. I am getting a dedicated 250W PoE switch to power the APs/Camaras, so I wont need the switch chip (i dont think).
View ArticleRe: Open ports
Your config suggests nothing is open and I'm not aware of any open issues related to such a problem with the platform. Personally I'd be confident you've nothing open and exposed but I'd probably also...
View ArticleRe: EdgePoint R6 switch configuration
Team: I'm having issues with the switch configuration on an EPR6. Not in the sense stuff isn't working cause it is. I will do my best to explain this. I have figured out having to drill down into...
View ArticleRe: Backing up ERPro-8 for failover.
So far I see he added conntrackd for conntrack syncing
View ArticleRe: 2 WAN 3 VLANs without load balance and failover
Well,the ER-PoE, doesn't have a vlan-aware switch-chip, if you create the vif's on the (parent) switch0 interface, these VLAN's will be applied on all the switchports (the eth interfaces that belong to...
View ArticleRouting to device with no gateway address
A device on my network has two interfaces (primary and secondary), and only 1 gateway address (which is associated with the primary interface). We're not able to modify the primary interface and...
View ArticleRe: Simple, modern IKEv2 VPN using PSK and no certificates
a detailed instructions would be very appreciated, thank you
View ArticleClik here to view.
Openvpn server supporting both udp and tcp
Hi, I’ve created 2 vtun interfaces, one accepting udp openvpn connection and the other for tcp so depending on my client needs they can choose one or the other. Udp is responding on 1194 and tcp on...
View ArticleRe: EdgePoint R6 switch configuration
You really should have started your own topic. If you want to reference this thread, do so with a link.
View ArticleLoopback Edgerouer lite LOCAL
I have a Edgerouter Lite.Connected to Internet with eth0, and servers connected to eth1. When I try to register my local edgerouter on my unms server, it doesn't work. I can register other edgerouters...
View ArticleRe: EdgeRouter Infinity - conntrack tuning
wrote:We run Infinitys as our core routers for our ISP, and we just upped the table size to 64 Million and all the problems went away... Jim, I understand and agree with everything you said, but I...
View ArticleRe: EdgePoint R6 switch configuration
I apologize on not using proper forum etiquette. Pretty new to communicating through one. I just leverage them on a daily basis by reading them. I was trying to figure out how to start a new topic...
View ArticleRe: EdgePoint R6 switch configuration
When doing what i said above i found "set interfaces switch switch0 switch-port vlan-aware enable" which is not in my configuration. When i tried to do that it saidThe specified configuration node is...
View ArticleRe: Loopback Edgerouer lite LOCAL
Why would you want that? I'm not sure hairpin world for the router itself but it's worth a try. If you don't know how to dip hairpin then look up the KB article on it. I don't have link on mobile
View ArticleRe: Wireless Printer - Waking Up
Hi, sorry for the delayed response. I've tried 2 printers, both with the same outcome. The current printer is an Epson WF-7720 and both were setup with a static IP address. I'm able to connect to the...
View Article